- Hybrid/EV Battery Current
- Hybrid/EV Battery Voltage
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001N34S |
| Model Year Start: 2021 | Model: Corolla | Prod Date Range: [04/2020 - 09/2022] |
| Title: HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with P610): P0ABF2A; Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range; 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022] | ||
|
DTC |
P0ABF2A |
Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range |
DESCRIPTION
Refer to the description for DTC P0ABF11.
Click here
![2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with P610): P0ABF11,...,P1CBB14; Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
|---|---|---|---|---|---|
|
P0ABF2A |
Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range |
The hybrid battery voltage is changing but the hybrid battery current and battery current sensor output do not change. (1 trip detection logic) |
|
Comes on |
Master Warning: Comes on |
Related Data List
|
DTC No. |
Data List |
|---|---|
|
P0ABF2A |
|
MONITOR DESCRIPTION
If the battery ECU assembly detects a malfunction in a battery current sensor, the battery ECU assembly will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs |
P0AC0 (INF P0ABF2A): Current sensor malfunction |
|
Required sensors/components |
Battery current sensor / Battery ECU assembly |
|
Frequency of operation |
Continuous |
|
Duration |
TMC's intellectual property |
|
MIL operation |
1 driving cycle |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Battery ECU assembly |
DTC P0AC0 (INF P0ABF2A) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
-
Drive the vehicle on urban roads for approximately 5 minutes.[*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
|
1. |
CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > HV Battery > Trouble Codes
Powertrain > Hybrid Control > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
"P0ABF2A" only is output, or DTCs except the ones in the table below are also output. |
A |
|
DTCs of hybrid battery system in the table below are output. |
B |
|
DTCs of hybrid control system in the table below are output. |
C |
|
System |
Relevant DTC |
|
|---|---|---|
|
Hybrid Battery System |
P060A47 |
Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure |
|
P060B49 |
Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure |
|
|
P060687 |
Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message |
|
|
P0ABF11 |
Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground |
|
|
P0ABF15 |
Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open |
|
|
P1CBB12 |
Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery |
|
|
P1CBB14 |
Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open |
|
|
Hybrid Control System |
P0A1F94 |
Hybrid/EV Battery Energy Control Module Unexpected Operation |
(e) Turn the power switch off.
| B |
|
| C |
|
|
|
2. |
CHECK DTC OUTPUT (HV BATTERY) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / HV Battery / Trouble Codes.
(d) Check for DTCs.
Powertrain > HV Battery > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
"P1A001C or P301A1C" is not output. |
A |
|
"P1A001C or P301A1C" is also output. |
B |
(e) Turn the power switch off.
| B |
|
|
|
3. |
READ VALUE USING TECHSTREAM (HYBRID/EV BATTERY CELL VOLTAGE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
NOTICE:
Do not turn the power switch on (READY).
(c) Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Cell 1 to 56 Voltage.
NOTICE:
Select "Hybrid/EV Battery Cell 1 to 56 Voltage" only. (Do not select any other Data List items.)
Powertrain > HV Battery > Data List
|
Tester Display |
|---|
|
Hybrid/EV Battery Cell 1 Voltage |
|
Hybrid/EV Battery Cell 2 Voltage |
|
Hybrid/EV Battery Cell 3 Voltage |
|
Hybrid/EV Battery Cell 4 Voltage |
|
Hybrid/EV Battery Cell 5 Voltage |
|
Hybrid/EV Battery Cell 6 Voltage |
|
Hybrid/EV Battery Cell 7 Voltage |
|
Hybrid/EV Battery Cell 8 Voltage |
|
Hybrid/EV Battery Cell 9 Voltage |
|
Hybrid/EV Battery Cell 10 Voltage |
|
Hybrid/EV Battery Cell 11 Voltage |
|
Hybrid/EV Battery Cell 12 Voltage |
|
Hybrid/EV Battery Cell 13 Voltage |
|
Hybrid/EV Battery Cell 14 Voltage |
|
Hybrid/EV Battery Cell 15 Voltage |
|
Hybrid/EV Battery Cell 16 Voltage |
|
Hybrid/EV Battery Cell 17 Voltage |
|
Hybrid/EV Battery Cell 18 Voltage |
|
Hybrid/EV Battery Cell 19 Voltage |
|
Hybrid/EV Battery Cell 20 Voltage |
|
Hybrid/EV Battery Cell 21 Voltage |
|
Hybrid/EV Battery Cell 22 Voltage |
|
Hybrid/EV Battery Cell 23 Voltage |
|
Hybrid/EV Battery Cell 24 Voltage |
|
Hybrid/EV Battery Cell 25 Voltage |
|
Hybrid/EV Battery Cell 26 Voltage |
|
Hybrid/EV Battery Cell 27 Voltage |
|
Hybrid/EV Battery Cell 28 Voltage |
|
Hybrid/EV Battery Cell 29 Voltage |
|
Hybrid/EV Battery Cell 30 Voltage |
|
Hybrid/EV Battery Cell 31 Voltage |
|
Hybrid/EV Battery Cell 32 Voltage |
|
Hybrid/EV Battery Cell 33 Voltage |
|
Hybrid/EV Battery Cell 34 Voltage |
|
Hybrid/EV Battery Cell 35 Voltage |
|
Hybrid/EV Battery Cell 36 Voltage |
|
Hybrid/EV Battery Cell 37 Voltage |
|
Hybrid/EV Battery Cell 38 Voltage |
|
Hybrid/EV Battery Cell 39 Voltage |
|
Hybrid/EV Battery Cell 40 Voltage |
|
Hybrid/EV Battery Cell 41 Voltage |
|
Hybrid/EV Battery Cell 42 Voltage |
|
Hybrid/EV Battery Cell 43 Voltage |
|
Hybrid/EV Battery Cell 44 Voltage |
|
Hybrid/EV Battery Cell 45 Voltage |
|
Hybrid/EV Battery Cell 46 Voltage |
|
Hybrid/EV Battery Cell 47 Voltage |
|
Hybrid/EV Battery Cell 48 Voltage |
|
Hybrid/EV Battery Cell 49 Voltage |
|
Hybrid/EV Battery Cell 50 Voltage |
|
Hybrid/EV Battery Cell 51 Voltage |
|
Hybrid/EV Battery Cell 52 Voltage |
|
Hybrid/EV Battery Cell 53 Voltage |
|
Hybrid/EV Battery Cell 54 Voltage |
|
Hybrid/EV Battery Cell 55 Voltage |
|
Hybrid/EV Battery Cell 56 Voltage |
(d) Check the voltage of each "Battery Cell Vol" of "Hybrid/EV Battery Cell 1 to 56 Voltage" in the Data List with the power switch on (IG).
Specified Condition:
Any "Hybrid/EV Battery Cell Voltage" changes by 0.05 V or more, 60 seconds after the power switch is turned on (IG). (The difference between the maximum and minimum voltage is 0.05 V or more.)
|
Result |
Proceed to |
|---|---|
|
The change in voltage of any "Hybrid/EV Battery Cell Voltage" is 0.05 V or more. |
A |
|
Other than above |
B |
(e) Turn the power switch off.
| A |
|
| B |
|
|
|