| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001N27V |
| Model Year Start: 2021 | Model: GR Corolla | Prod Date Range: [04/2020 - 09/2022] |
| Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: Speaker Circuit; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022] | ||
|
Speaker Circuit |
DESCRIPTION
w/o Stereo Component Amplifier Assembly
-
If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, DCM (telematics transceiver)* or speakers.
w/ Stereo Component Amplifier Assembly
-
If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)* or speakers.
- *: w/ Manual (SOS) Switch
WIRING DIAGRAM
for 6 Speakers
for 8 Speakers
for 9 Speakers
CAUTION / NOTICE / HINT
NOTICE:
-
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
![2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
Before replacing the DCM (telematics transceiver), refer to Registration.
Click here
PROCEDURE
|
1. |
CHECK MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for 6 Speakers |
A |
|
for 8 Speakers |
B |
|
for 9 Speakers |
C |
| B |
|
| C |
|
|
|
2. |
CHECK SPEAKER (OPERATION CHECK) |
|
(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check. Click here
|
|
(b) Perform the operation check above and determine the speaker that is not operating.
|
Not Operating Speaker |
Proceed to |
|---|---|
|
Front No. 1 speaker assembly or front No. 2 speaker assembly (w/o Manual (SOS) Switch) |
A |
|
Front No. 1 speaker assembly or front No. 2 speaker assembly (w/ Manual (SOS) Switch) |
B |
|
Rear speaker assembly |
C |
HINT:
If sound cannot be heard from any speaker, inspect all of them.
| B |
|
| C |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I71 radio and display receiver assembly connector.
(b) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.
(c) Disconnect the I76 and I77 front No. 2 speaker assembly connectors.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I71-1 (FR+) - I76-4 (TWR+) |
Always |
Below 1 Ω |
|
I71-6 (FR-) - I76-2 (TWR-) |
Always |
Below 1 Ω |
|
I71-2 (FL+) - I77-4 (TWL+) |
Always |
Below 1 Ω |
|
I71-7 (FL-) - I77-2 (TWL-) |
Always |
Below 1 Ω |
|
K1-2 - I76-3 (+) |
Always |
Below 1 Ω |
|
K1-1 - I76-1 (-) |
Always |
Below 1 Ω |
|
L1-2 - I77-3 (+) |
Always |
Below 1 Ω |
|
L1-1 - I77-1 (-) |
Always |
Below 1 Ω |
|
I71-1 (FR+) or I76-4 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
I71-6 (FR-) or I76-2 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
I71-2 (FL+) or I77-4 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
I71-7 (FL-) or I77-2 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
K1-2 or I76-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
K1-1 or I76-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
L1-2 or I77-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
L1-1 or I77-1 (-) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
4. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I71 radio and display receiver assembly connector.
(b) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.
(c) Disconnect the I76 and I77 front No. 2 speaker assembly connectors.
(d) Disconnect the I144 DCM (telematics transceiver) connector.
(e) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I71-1 (FR+) - I144-1 (SPI+) |
Always |
Below 1 Ω |
|
I71-6 (FR-) - I144-2 (SPI-) |
Always |
Below 1 Ω |
|
I144-3 (SPO+) - I76-4 (TWR+) |
Always |
Below 1 Ω |
|
I144-4 (SPO-) - I76-2 (TWR-) |
Always |
Below 1 Ω |
|
I71-2 (FL+) - I77-4 (TWL+) |
Always |
Below 1 Ω |
|
I71-7 (FL-) - I77-2 (TWL-) |
Always |
Below 1 Ω |
|
K1-2 - I76-3 (+) |
Always |
Below 1 Ω |
|
K1-1 - I76-1 (-) |
Always |
Below 1 Ω |
|
L1-2 - I77-3 (+) |
Always |
Below 1 Ω |
|
L1-1 - I77-1 (-) |
Always |
Below 1 Ω |
|
I71-1 (FR+) or I144-1 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
I71-6 (FR-) or I144-2 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
I71-2 (FL+) or I77-4 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
I71-7 (FL-) or I77-2 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
I144-3 (SPO+) or I76-4 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
I144-4 (SPO-) or I76-2 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
K1-2 or I76-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
K1-1 or I76-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
L1-2 or I77-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
L1-1 or I77-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG |
|
|
|
6. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
7. |
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
OK:
Malfunction disappears.
| OK |
|
END |
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
8. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
(a) Disconnect the I71 radio and display receiver assembly connector.
(b) Disconnect the N4 and M4 rear speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I71-4 (RR+) - M4-2 |
Always |
Below 1 Ω |
|
I71-9 (RR-) - M4-1 |
Always |
Below 1 Ω |
|
I71-3 (RL+) - N4-2 |
Always |
Below 1 Ω |
|
I71-8 (RL-) - N4-1 |
Always |
Below 1 Ω |
|
I71-4 (RR+) or M4-2 - Body ground |
Always |
10 kΩ or higher |
|
I71-9 (RR-) or M4-1 - Body ground |
Always |
10 kΩ or higher |
|
I71-3 (RL+) or N4-2 - Body ground |
Always |
10 kΩ or higher |
|
I71-8 (RL-) or N4-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
10. |
CHECK SPEAKER (OPERATION CHECK) |
|
(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check. Click here
|
|
(b) Perform the operation check above and determine the speaker that is not operating.
|
Not Operating Speaker |
Proceed to |
|---|---|
|
Front No. 1 speaker assembly or front No. 3 speaker assembly |
A |
|
Front No. 2 speaker assembly |
B |
|
Rear speaker assembly |
C |
|
Rear No. 2 Speaker Assembly |
D |
HINT:
If sound cannot be heard from any speaker, inspect all of them.
| B |
|
| C |
|
| D |
|
|
|
11. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.
(c) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-15 (FR+) - I74-4 (+TW) |
Always |
Below 1 Ω |
|
I54-30 (FR-) - I74-2 (-TW) |
Always |
Below 1 Ω |
|
I54-13 (FL+) - I75-4 (+TW) |
Always |
Below 1 Ω |
|
I54-28 (FL-) - I75-2 (-TW) |
Always |
Below 1 Ω |
|
K1-2 - I74-3 (+) |
Always |
Below 1 Ω |
|
K1-1 - I74-1 (-) |
Always |
Below 1 Ω |
|
L1-2 - I75-3 (+) |
Always |
Below 1 Ω |
|
L1-1 - I75-1 (-) |
Always |
Below 1 Ω |
|
I54-15 (FR+) or I74-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
I54-30 (FR-) or I74-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
I54-13 (FL+) or I75-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
I54-28 (FL-) or I75-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K1-2 or I74-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
K1-1 or I74-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
L1-2 or I75-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
L1-1 or I75-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
12. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
13. |
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY |
(a) Remove the front No. 3 speaker assembly.
Click here
(b) Inspect the front No. 3 speaker assembly.
Click here
OK:
Malfunction disappears.
| OK |
|
END |
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
14. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the I6 and I7 front No. 2 speaker assembly connectors.
(c) Disconnect the I144 DCM (telematics transceiver) connector.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-14 (TWR+) - I144-1 (SPI+) |
Always |
Below 1 Ω |
|
I54-29 (TWR-) - I144-2 (SPI-) |
Always |
Below 1 Ω |
|
I144-3 (SPO+) - I6-2 |
Always |
Below 1 Ω |
|
I144-4 (SPO-) - I6-1 |
Always |
Below 1 Ω |
|
I54-12 (TWL+) - I7-2 |
Always |
Below 1 Ω |
|
I54-27 (TWL-) - I7-1 |
Always |
Below 1 Ω |
|
I54-14 (TWR+) or I144-1 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
I54-29 (TWR-) or I144-2 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
I54-12 (TWL+) or I7-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-27 (TWL-) or I7-1 - Body ground |
Always |
10 kΩ or higher |
|
I144-3 (SPO+) or I6-2 - Body ground |
Always |
10 kΩ or higher |
|
I144-4 (SPO-) or I6-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
15. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| NG |
|
|
|
16. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
17. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the M4 and N4 rear speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-11 (RR+) - M4-2 |
Always |
Below 1 Ω |
|
I54-26 (RR-) - M4-1 |
Always |
Below 1 Ω |
|
I54-9 (RL+) - N4-2 |
Always |
Below 1 Ω |
|
I54-24 (RL-) - N4-1 |
Always |
Below 1 Ω |
|
I54-11 (RR+) or M4-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-26 (RR-) or M4-1 - Body ground |
Always |
10 kΩ or higher |
|
I54-9 (RL+) or N4-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-24 (RL-) or N4-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
18. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
19. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the O71 rear No. 2 speaker assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-10 (WF1+) - O71-4 (WF1+) |
Always |
Below 1 Ω |
|
I54-25 (WF1-) - O71-3 (WF1-) |
Always |
Below 1 Ω |
|
I54-8 (WF2+) - O71-2 (WF2+) |
Always |
Below 1 Ω |
|
I54-23 (WF2-) - O71-1 (WF2-) |
Always |
Below 1 Ω |
|
I54-10 (WF1+) or O71-4 (WF1+) - Body ground |
Always |
10 kΩ or higher |
|
I54-25 (WF1-) or O71-3 (WF1-) - Body ground |
Always |
10 kΩ or higher |
|
I54-8 (WF2+) or O71-2 (WF2+) - Body ground |
Always |
10 kΩ or higher |
|
I54-23 (WF2-) or O71-1 (WF2-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
20. |
INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
(a) Remove the rear No. 2 speaker assembly.
Click here
(b) Inspect the rear No. 2 speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
21. |
CHECK SPEAKER (OPERATION CHECK) |
|
(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check. Click here
|
|
(b) Perform the operation check above and determine the speaker that is not operating.
|
Not Operating Speaker |
Proceed to |
|---|---|
|
Front No. 1 speaker assembly or front No. 3 speaker assembly |
A |
|
Front No. 2 speaker assembly (w/ Manual (SOS) Switch) |
B |
|
Front No. 2 speaker assembly (w/o Manual (SOS) Switch) |
C |
|
Rear speaker assembly |
D |
|
Rear No. 2 Speaker Assembly |
E |
HINT:
If sound cannot be heard from any speaker, inspect all of them.
| B |
|
| C |
|
| D |
|
| E |
|
|
|
22. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.
(c) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-15 (FR+) - I74-4 (+TW) |
Always |
Below 1 Ω |
|
I54-30 (FR-) - I74-2 (-TW) |
Always |
Below 1 Ω |
|
I54-13 (FL+) - I75-4 (+TW) |
Always |
Below 1 Ω |
|
I54-28 (FL-) - I75-2 (-TW) |
Always |
Below 1 Ω |
|
K1-2 - I74-3 (+) |
Always |
Below 1 Ω |
|
K1-1 - I74-1 (-) |
Always |
Below 1 Ω |
|
L1-2 - I75-3 (+) |
Always |
Below 1 Ω |
|
L1-1 - I75-1 (-) |
Always |
Below 1 Ω |
|
I54-15 (FR+) or I74-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
I54-30 (FR-) or I74-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
I54-13 (FL+) or I75-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
I54-28 (FL-) or I75-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K1-2 or I74-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
K1-1 or I74-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
L1-2 or I75-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
L1-1 or I75-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
23. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
24. |
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY |
(a) Remove the front No. 3 speaker assembly.
Click here
(b) Inspect the front No. 3 speaker assembly.
Click here
OK:
Malfunction disappears.
| OK |
|
END |
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
25. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the I6 and I7 front No. 2 speaker assembly connectors.
(c) Disconnect the I72 DCM (telematics transceiver) connector.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-14 (TWR+) - I72-2 (SPI+) |
Always |
Below 1 Ω |
|
I54-29 (TWR-) - I72-3 (SPI-) |
Always |
Below 1 Ω |
|
I72-5 (SPO+) - I6-2 |
Always |
Below 1 Ω |
|
I72-6 (SPO-) - I6-1 |
Always |
Below 1 Ω |
|
I54-12 (TWL+) - I7-2 |
Always |
Below 1 Ω |
|
I54-27 (TWL-) - I7-1 |
Always |
Below 1 Ω |
|
I54-14 (TWR+) or I72-2 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
I54-29 (TWR-) or I72-3 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
I54-12 (TWL+) or I7-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-27 (TWL-) or I7-1 - Body ground |
Always |
10 kΩ or higher |
|
I72-5 (SPO+) or I6-2 - Body ground |
Always |
10 kΩ or higher |
|
I72-6 (SPO-) or I6-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
26. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| NG |
|
|
|
27. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
28. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the I6 and I7 front No. 2 speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-14 (TWR+) - I6-2 |
Always |
Below 1 Ω |
|
I54-29 (TWR-) - I6-1 |
Always |
Below 1 Ω |
|
I54-12 (TWL+) - I7-2 |
Always |
Below 1 Ω |
|
I54-27 (TWL-) - I7-1 |
Always |
Below 1 Ω |
|
I54-14 (TWR+) or I6-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-29 (TWR-) or I6-1 - Body ground |
Always |
10 kΩ or higher |
|
I54-12 (TWL+) or I7-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-27 (TWL-) or I7-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
29. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
30. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the M4 and N4 rear speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-11 (RR+) - M4-2 |
Always |
Below 1 Ω |
|
I54-26 (RR-) - M4-1 |
Always |
Below 1 Ω |
|
I54-9 (RL+) - N4-2 |
Always |
Below 1 Ω |
|
I54-24 (RL-) - N4-1 |
Always |
Below 1 Ω |
|
I54-11 (RR+) or M4-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-26 (RR-) or M4-1 - Body ground |
Always |
10 kΩ or higher |
|
I54-9 (RL+) or N4-2 - Body ground |
Always |
10 kΩ or higher |
|
I54-24 (RL-) or N4-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
31. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
32. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the I54 stereo component amplifier assembly connector.
(b) Disconnect the O71 rear No. 2 speaker assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I54-10 (WF1+) - O71-4 (WF1+) |
Always |
Below 1 Ω |
|
I54-25 (WF1-) - O71-3 (WF1-) |
Always |
Below 1 Ω |
|
I54-8 (WF2+) - O71-2 (WF2+) |
Always |
Below 1 Ω |
|
I54-23 (WF2-) - O71-1 (WF2-) |
Always |
Below 1 Ω |
|
I54-10 (WF1+) or O71-4 (WF1+) - Body ground |
Always |
10 kΩ or higher |
|
I54-25 (WF1-) or O71-3 (WF1-) - Body ground |
Always |
10 kΩ or higher |
|
I54-8 (WF2+) or O71-2 (WF2+) - Body ground |
Always |
10 kΩ or higher |
|
I54-23 (WF2-) or O71-1 (WF2-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
33. |
INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
(a) Remove the rear No. 2 speaker assembly.
Click here
(b) Inspect the rear No. 2 speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
|
|
|