Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM100000001N265 |
Model Year Start: 2021 |
Model: GR Corolla |
Prod Date Range: [04/2020 - 11/2022] |
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for Gasoline Model with Dual Knob Type): B1579; Voice Recognition Microphone Disconnected; 2021 - 2023 MY Corolla Corolla Hatchback GR Corolla [04/2020 - 11/2022] |
DTC
|
B1579
|
Voice Recognition Microphone Disconnected
|
DESCRIPTION
The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B1579
|
Voice Recognition Microphone Disconnected
|
Microphone signal is lost
|
-
Map light assembly
-
Telephone microphone assembly
-
Radio and display receiver assembly
-
DCM (telematics transceiver)*
-
Harness or connector
|
-
*: w/ Manual (SOS) Switch
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I56-22 (MIN-) - Body ground
|
Always
|
Below 1 Ω
|
Result:
Result
|
Proceed to
|
OK (w/o Manual (SOS) Switch)
|
A
|
OK (w/ Manual (SOS) Switch)
|
B
|
NG
|
C
|
|
|
*a
|
Component with harness connected
(Radio and Display Receiver Assembly)
|
|
|
A
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
|
(a) Disconnect the I56 radio and display receiver assembly connector.
(b) Disconnect the T6 map light assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I56-25 (SNS2) - T6-4 (SNS2)
|
Always
|
Below 1 Ω
|
I56-22 (MIN-) - T6-5 (MCO-)
|
Always
|
Below 1 Ω
|
I56-25 (SNS2) or T6-4 (SNS2) - Body ground
|
Always
|
10 kΩ or higher
|
I56-22 (MIN-) or T6-5 (MCO-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
3.
|
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - MAP LIGHT ASSEMBLY)
|
(a) Disconnect the I143 DCM (telematics transceiver) connector.
(b) Disconnect the T6 map light assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I143-7 (MCI-) - T6-5 (MCO-)
|
Always
|
Below 1 Ω
|
I143-7 (MCI-) or T6-5 (MCO-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
|
(a) Disconnect the I56 radio and display receiver assembly connector.
(b) Disconnect the I143 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I56-22 (MIN-) - I143-32 (MCO-)
|
Always
|
Below 1 Ω
|
I56-22 (MIN-) or I143-32 (MCO-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
|
(a) Disconnect the I56 radio and display receiver assembly connector.
(b) Disconnect the T6 map light assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I56-25 (SNS2) - T6-4 (SNS2)
|
Always
|
Below 1 Ω
|
I56-25 (SNS2) or T6-4 (SNS2) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
6.
|
INSPECT DCM (TELEMATICS TRANSCEIVER)
|
(a) Connect the I143 DCM (telematics transceiver) connector.
(b) Connect the I56 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I143-7 (MCI-) - Body ground
|
Always
|
Below 1 Ω
|
|
|
*a
|
Component with harness connected
(DCM (Telematics Transceiver))
|
|
|
OK
|
|
|
7.
|
INSPECT MAP LIGHT ASSEMBLY
|
(a) Remove the map light assembly.
Click here
(b) Connect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
4 (SNS2) - 5 (MCO-)
|
Always
|
Below 1 Ω
|
|
|
*a
|
Component without harness connected
(Map Light Assembly)
|
|
|
NG
|
|
|
8.
|
INSPECT MAP LIGHT ASSEMBLY
|
(a) Remove the map light assembly.
Click here
(b) Disconnect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
B-1 - T6-4 (SNS2)
|
Always
|
Below 1 Ω
|
B-2 - T6-5 (MCO-)
|
Always
|
Below 1 Ω
|
B-1 or T6-4 (SNS2) - T6-11 (GND)
|
Always
|
10 kΩ or higher
|
B-2 or T6-5 (MCO-) - T6-11 (GND)
|
Always
|
10 kΩ or higher
|
|
|
*a
|
Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
|
*b
|
Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))
|
|
|
|