INTERIOR PANELS / TRIM: ROOF HEADLINING (for Sedan): REMOVAL; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001N20O
Model Year Start: 2021	Model: GR Corolla	Prod Date Range: [04/2020 - 09/2022]
Title: INTERIOR PANELS / TRIM: ROOF HEADLINING (for Sedan): REMOVAL; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*1: for Hatchback
Disconnect cable from negative (-) battery terminal	Perform steering sensor zero point calibration	Lane Control System (for Gasoline Model)
		Pre-collision System (for Gasoline Model)
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock*1	Power Door Lock Control System (for Hatchback, Gasoline Model)

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for TMC Made Gasoline Model: Click here

for TMMMS Made: Click here

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System (for HV Model)
	Perform steering sensor zero point calibration	Pre-collision System (for HV Model)

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

PROCEDURE

1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Click here

2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Click here

3. REMOVE REAR SEAT ASSEMBLY

Click here

4. REMOVE FRONT DOOR SCUFF PLATE LH

Click here

5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Click here

6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

7. REMOVE FRONT PILLAR GARNISH LH

Click here

8. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)

Click here

9. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)

(a) Disengage the claw as shown in the illustration.

	Place Hand Here
	Remove in this Direction

(b) Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.

Remove in this Direction

10. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

11. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Click here

12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

13. REMOVE CENTER PILLAR LOWER GARNISH LH

Click here

14. REMOVE CENTER PILLAR UPPER GARNISH LH

Click here

15. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

18. REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

19. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

20. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

21. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

22. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

23. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.

24. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.

25. REMOVE REAR UNDER SIDE COVER LH (for HV Model)

(a) Remove the 2 clips.

Remove in this Direction

(b) Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.

26. REMOVE REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)

(a) Disengage the clip, 2 claws and 2 guides.

(b) Pass the rear seatback hinge sub-assembly LH through the rear seat side garnish LH as shown in the illustration and remove the rear seat side garnish LH.

*1	Rear Seatback Hinge Sub-assembly LH
	Remove in this Direction

27. REMOVE REAR SEAT SIDE GARNISH LH (w/ Rear Seat Side Airbag)

(a) Disengage the 8 claws and 4 guides.

(b) Pass the rear seatback hinge sub-assembly LH through the rear seat side garnish LH as shown in the illustration and remove the rear seat side garnish LH.

*1	Rear Seatback Hinge Sub-assembly LH
	Remove in this Direction

28. REMOVE ROOF SIDE INNER GARNISH LH

(a) Disengage the 3 clips as shown in the illustration.

	Place Hand Here
	Remove in this Direction

(b) Disengage the 2 guides to remove the roof side inner garnish LH as shown in the illustration.

Remove in this Direction

29. REMOVE REAR UNDER SIDE COVER RH (for HV Model)

HINT:

Use the same procedure as for the LH side.

30. REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

31. REMOVE ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

32. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

33. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for HV Model)

Click here

34. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for Manual Transaxle)

for EG60: Click here

for EC65: Click here

35. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for CVT)

for K313: Click here

for K120: Click here

36. REMOVE MAP LIGHT ASSEMBLY

Click here

37. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Click here

38. REMOVE VANITY LIGHT ASSEMBLY (w/ Vanity Light)

Click here

39. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

Click here

40. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Click here

41. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Click here

42. REMOVE ASSIST GRIP SUB-ASSEMBLY

Click here

43. REMOVE REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip sub-assembly.

44. REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip sub-assembly.

45. REMOVE VISOR ASSEMBLY LH

Click here

46. REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

47. REMOVE ROOF HEADLINING ASSEMBLY

(a) for Windshield Glass Side with Connector:

(1) Disconnect each connector.

(b) for Front Pillar LH Side:

(1) Remove the protective cover.

(2) Using a clip remover, disengage the 4 clamps.

(3) Disconnect the 2 connectors.

(4) Install the protective cover.

(1) Remove the protective cover.

(2) Using a clip remover, disengage the 3 clamps.

(3) Disconnect each connector.

(4) Install the protective cover.

(d) for Rear Pillar RH Side:

(1) Disconnect the 2 connectors.

(2) Disengage the clamp.

(e) Turn the visor holder approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.

*a	45°
	Remove in this Direction (1)
	Remove in this Direction (2)

HINT:

Use the same procedure for the LH side and RH side.

(f) for Roof Side (for Normal Roof):

(1) Disengage the 2 claws to remove the base of each visor holder.

Base of Visor Holder

(2) Using a clip remover, remove the 3 clips.

(g) for Roof Side (for Moon Roof):

(1) Disconnect the connector.

Base of Visor Holder

(2) Disengage the 2 claws to remove the base of each visor holder.

(3) Using a clip remover, remove the 3 clips.

(4) Disengage the 6 fasteners.

(h) Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.

Remove in this Direction

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.