POWER ASSIST SYSTEMS: POWER STEERING SYSTEM (for Gasoline Model): VEHICLE CONTROL HISTORY; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [09/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001KGXF
Model Year Start: 2020	Model: GR Corolla	Prod Date Range: [09/2019 - 09/2022]
Title: POWER ASSIST SYSTEMS: POWER STEERING SYSTEM (for Gasoline Model): VEHICLE CONTROL HISTORY; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [09/2019 - 09/2022]

VEHICLE CONTROL HISTORY

DESCRIPTION

Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.
It may be possible to determine the cause of the malfunction by checking the vehicle history information and freeze frame data.
The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.
Click here

PRECAUTIONS

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.
As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.

CHECK VEHICLE CONTROL HISTORY (POWER STEERING SYSTEM)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / EMPS / Utility / Vehicle Control History (RoB).

Chassis > EMPS > Utility

Tester Display
Vehicle Control History (RoB)

Vehicle Control History Item (Power Steering System)

FFD Group	Code	Tester Display	Measurement Item	Diagnostic Note
-	X200C	Vehicle Speed Signal Invalidity	Latest vehicle speed signal invalid history Latest vehicle speed signal fault control history (applicable only when CAN Vehicle Speed (SP1) is invalid)	-
-	X206D	Power Source Stop	Latest Engine Stall/READY OFF Control History	-
-	X206E	High Load Continuation	Latest High Load Continuous Control Number of Times	-
-	X206F	Prevention of ECU/Motor Overheat	Latest Overheat Prevention Control History	-
-	X208F	Battery Voltage Drop	Latest Battery Voltage Drop History Latest Power Supply Voltage Drop Control History Latest Power Supply Voltage Drop Restraint Control History Latest Chassis Power Supply Management EPS Control History Latest Load Control History	-
-	X2600	Software Incompatibility with ENG/HV Control Module (Not Programmed)	History stored when vehicle information (gasoline/HV) is not stored	-
-	X2601	Software Inconsistency with ENG/HV Control Module	History stored when Assist Map Writing has not been performed History stored when assist map data does not match History stored when vehicle information (gasoline/HV) does not match	-
-	X2603	Software Inconsistency with Body Control Module	History stored when Assist Map Writing has not been performed History stored when assist map data does not match	-
-	X2605	Software Inconsistency with Brake Control Module	History stored when Assist Map Writing has not been performed History stored when assist map data does not match	-
-	X2606	Software Inconsistency with Suspension Control Module	History stored when Assist Map Writing has not been performed History stored when assist map data does not match	-
-	X2608	Software Incompatibility with VGRS Control Module (Not Programmed)	History stored when vehicle information (variable gear ratio steering system) not stored	-
-	X2609	Software Inconsistency with VGRS Control Module	History stored when vehicle information (variable gear ratio steering system) does not match	-
-	X260A	Software Incompatibility with DRS Control Module (Not Programmed)	History stored when vehicle information (dynamic rear steering system) not stored	-
-	X260B	Software Inconsistency with DRS Control Module	History stored when vehicle information (dynamic rear steering system) does not match	-
-	X260D	Software Inconsistency with Steering Angle Sensor Module	History stored when vehicle information (variable gear ratio steering system) does not match	-
-	X2610	Torque Sensor Missing Calibration of Adjustment Value Non-Memory	History stored when zero point calibration not performed	-
-	X2611	Torque Sensor Missing Calibration of Adjustment Incomplete	History stored when zero point calibration failed	-
-	X2612	Assist Map Non-Memory	History stored when Assist Map Writing has not been performed	-

CLEAR VEHICLE CONTROL HISTORY (POWER STEERING SYSTEM)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / EMPS / Utility / Vehicle Control History (RoB).

Chassis > EMPS > Utility

Tester Display
Vehicle Control History (RoB)

(f) Press the DTC clear button.

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.

VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)

HINT:

A part of the control history can be confirmed using the vehicle control history.

for TMMMS Made: Click here

for TMC Made: Click here