Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001I1JQ |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [03/2019 - 09/2022] |
Title: EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock*1
|
Power Door Lock Control System
|
|
-
Front door glass sub-assembly
-
Front door glass run
-
Front door belt moulding
-
Front door inner glass weatherstrip
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative (-) auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
-
Front door glass sub-assembly
-
Front door glass run
-
Front door belt moulding
-
Front door inner glass weatherstrip
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
NOTICE:
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for M20A-FKS:
Click here
for 2ZR-FAE:
Click here
for 2ZR-FXE:
Click here
3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Click here
4. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY
Click here
5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE DOOR UPPER FRAME GARNISH
Click here
9. REMOVE FRONT DOOR VENT SEAL
Click here
10. REMOVE NO. 3 FRONT DOOR SERVICE HOLE COVER
Click here
11. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
13. REMOVE FRONT DOOR GLASS RUN
Click here
14. DISCONNECT FRONT DOOR WEATHERSTRIP
(a) Disconnect the front door weatherstrip until the screw of the front door front lower frame sub-assembly is visible.
15. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Click here
16. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP WITH FRONT DOOR FIX WINDOW GLASS
Click here
17. REMOVE FRONT DOOR BELT MOULDING
(a) Apply protective tape around the front door belt moulding as shown in the illustration.
|
Protective Tape
|
|
Remove in this Direction
|
(b) Disengage the 8 claws as shown in the illustration to remove the front door belt moulding.
|