Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001I1GC |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 09/2022] |
Title: M20A-FKS (INTAKE / EXHAUST): EXHAUST MANIFOLD (for Double Wishbone Type Suspension): REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold (TWC: Front Catalyst) removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
-
Replacement of air fuel ratio sensor (sensor 1)
-
Gas leaks from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
CAUTION:
-
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
-
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
PROCEDURE
1. REMOVE FRONT FLOOR COVER LH
(a) for Hatchback:
*A
|
Type A
|
*B
|
Type B
|
|
Bolt
|
|
Clip
|
(1) Remove the 2 bolts and 3 clips and disengage the 6 clamps to remove the front floor cover LH from the vehicle body.
|
Bolt
|
|
Clip
|
(b) except Hatchback:
(1) w/ Cover:
Remove the 2 bolts and 3 clips and disengage the 6 clamps to remove the front floor cover LH from the vehicle body.
2. REMOVE FRONT FLOOR COVER RH
HINT:
Perform the same procedure as for the front floor cover LH.
3. REMOVE FRONT FLOOR CENTER BRACE
(a) for Hatchback:
(1) Remove the 12 bolts and 3 front floor center braces from the vehicle body.
|
|
(b) except Hatchback:
(1) Remove the 8 bolts and 2 front floor center braces from the vehicle body.
|
|
4. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
CAUTION:
-
To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.
-
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
(a) Disconnect the air fuel ratio sensor connector.
|
|
(b) Disengage the wire harness clamp.
(c) Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst) and tail exhaust pipe assembly.
|
|
*A
|
for Hatchback
|
*B
|
except Hatchback
|
|
|
(d) Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.
(e) Remove the 2 gaskets from the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).
5. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
-
for Manual Transaxle:
-
for CVT:
6. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here
7. REMOVE AIR FUEL RATIO SENSOR
Click here
8. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.
(a) Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).
|
|
9. REMOVE MANIFOLD STAY
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.
(a) Remove the bolt, nut and manifold stay from the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly.
|
|
10. REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.
(a) Using a 12 mm deep socket wrench, remove the 7 nuts and exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.
|
|
(b) Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.
|
|
11. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
(a) Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).
|
|
|