| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001I0M5 |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [03/2019 - 09/2022] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System): C13807E; Stop Lamp Relay Actuator Stuck On; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [03/2019 - 09/2022] | ||
|
DTC |
C13807E |
Stop Lamp Relay Actuator Stuck On |
DESCRIPTION
When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.
Illumination Conditions:
- Pre-collision brake is operating.*
- The dynamic radar cruise control system is operating and is applying the brakes.*
- Secondary collision brake is operating.
- *: w/ Pre-collision System
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C13807E |
Stop Lamp Relay Actuator Stuck On |
When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is off, the signal at the STP2 terminal is different from the input signal at the STP terminal for 5 seconds or more. |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
Click here
![2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [03/2019 - 09/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System): UTILITY](/t3Portal/stylegraphics/info.gif)
HINT:
When DTC P057111, P057112 and/or P057113 are output together with DTC C13807E, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.
P057111: Click here
P057112: Click here
P057113: Click here
PROCEDURE
|
1. |
CHECK STOP LIGHT ILLUMINATION STATUS |
(a) With the brake pedal released, check the illumination status of the brake lights.
|
Result |
Proceed to |
|---|---|
|
The stop lights are illuminated. |
A |
|
The stop lights are not illuminated. |
B |
| B |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY CIRCUIT) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector. OK: The connector is securely connected. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A53-4 (ACC) - Body ground |
Always |
11 to 14 V |
| NG |
|
|
|
3. |
CHECK STOP LIGHT ILLUMINATION STATUS |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the A53 stop light switch assembly connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Check the illumination status of the brake lights.
|
Result |
Proceed to |
|---|---|
|
The stop lights are illuminated. |
A |
|
The stop lights are not illuminated. |
B |
| B |
|
|
|
4. |
CHECK STOP LIGHT ILLUMINATION STATUS |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the A53 stop light switch assembly connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Check the illumination status of the brake lights.
|
Result |
Proceed to |
|---|---|
|
The stop lights are illuminated. |
A |
|
The stop lights are not illuminated. |
B |
| A |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CIRCUIT) |
| B |
|
|
5. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY CIRCUIT) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors. OK: The connector is securely connected. |
|
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A53-4 (ACC) - Body ground |
Always |
11 to 14 V |
| OK |
|
|
|
6. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the A53 stop right switch assembly connector.
(c) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A53-4 (ACC) or A100-3 (STPO) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
7. |
CHECK STOP LIGHT OPERATION |
(a) Check that the stop lights come on when the brake pedal is depressed.
OK:
The stop lights illuminate.
| NG |
|
|
|
8. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors. OK: The connector is securely connected. |
|
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A100-24 (STP2) - Body ground |
Brake pedal depressed |
11 to 14 V |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
9. |
CHECK STOP LIGHT OPERATION |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Check that the stop lights come on when the brake pedal is depressed.
OK:
The stop lights illuminate.
| OK |
|
|
|
10. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors. OK: The connector is securely connected. |
|
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the O104 rear combination light assembly LH connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O104-2 (STP) - Body ground |
Brake pedal depressed |
11 to 14 V |
| OK |
|
GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT)) Refer to "Left or right stop light does not illuminate" of problem symptoms table. w/ AFS: Click here
w/o AFS: Click here
|
|
|
11. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors. OK: The connector is securely connected. |
|
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the O104 rear combination light assembly LH connector.
(d) Disconnect the O103 rear combination light assembly RH connector.
(e) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(f) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O103-2 (STP) - Body ground |
Brake pedal depressed |
11 to 14 V |
| OK |
|
GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT)) Refer to "Left or right stop light does not illuminate" of problem symptoms table. w/ AFS: Click here
w/o AFS: Click here
|
|
|
12. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY) |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors. OK: The connector is securely connected. |
|
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the O104 rear combination light assembly LH connector.
(d) Disconnect the O103 rear combination light assembly RH connector.
(e) Disconnect the O111 center stop light set connector.
(f) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(g) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O111-1 (B) - Body ground |
Brake pedal depressed |
11 to 14 V |
| OK |
|
|
|
13. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH) |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the A100 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the O104 rear combination light assembly LH connector.
(d) Disconnect the O103 rear combination light assembly RH connector.
(e) Disconnect the O111 center stop light set connector.
(f) Disconnect the A53 stop light switch assembly connector.
(g) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A53-1 (OUT) - O104-2 (STP) |
Always |
Below 1 Ω |
|
A53-1 (OUT) or O104-2 (STP) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|