| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001I08A |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [03/2019 - 09/2022] |
| Title: HEATING / AIR CONDITIONING: BLOWER UNIT: REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during blower unit removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for HV Model) |
|
|
Pre-collision System (for HV Model) |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2020 MY Corolla Corolla HV [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
HINT:
Before removing the blower assembly, set the air conditioning to recirculation mode.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
| *1: for Hatchback | |||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for Gasoline Model) |
|
|
Pre-collision System (for Gasoline Model) |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock*1 |
Power Door Lock Control System (for Hatchback, Gasoline Model) |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for TMC Made Gasoline Model:Click here
for TMMMS Made: Click here
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
HINT:
Before removing the blower assembly, set the air conditioning to recirculation mode.
PROCEDURE
1. REMOVE AIR CONDITIONER UNIT ASSEMBLY
Click here
2. REMOVE NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)
Click here
3. REMOVE NO. 2 AIR DUCT
Click here
4. REMOVE BLOWER ASSEMBLY
|
(a) Disconnect the connector. |
|
(b) Disengage each guide.
|
(c) Remove the 2 screws. |
|
(d) Disengage the 2 claws and 3 guides and remove the blower assembly from the air conditioning radiator assembly.
|
|