DOOR / HATCH: LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001I068
Model Year Start: 2020	Model: GR Corolla	Prod Date Range: [03/2019 - 04/2020]
Title: DOOR / HATCH: LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 04/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during luggage door lock control cable sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed
*1: for Hatchback
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision System
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock*1	Power Door Lock Control System

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

for TMC Made Gasoline Model:

Click here

for TMMMS Made:

Click here

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Pre-collision System

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

PROCEDURE

1. REMOVE FRONT SEAT ASSEMBLY LH

for Manual Seat:

Click here

for Power Seat:

Click here

2. REMOVE REAR SEAT ASSEMBLY

Click here

3. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)

Click here

4. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)

Click here

5. REMOVE REAR UNDER SIDE COVER LH (for HV Model)

Click here

6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

7. REMOVE REAR SEAT SIDE GARNISH LH

Click here

8. REMOVE FRONT DOOR SCUFF PLATE LH

Click here

9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Click here

10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

11. REMOVE LAP BELT OUTER ANCHOR COVER

Click here

12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

13. REMOVE CENTER PILLAR LOWER GARNISH LH

Click here

14. REMOVE ROOF SIDE INNER GARNISH LH

Click here

15. REMOVE ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

16. REMOVE CENTER STOP LIGHT SET

Click here

17. REMOVE PACKAGE TRAY TRIM BRACKET LH

Click here

18. REMOVE PACKAGE TRAY TRIM BRACKET RH

HINT:

Use the same procedure as for the LH side.

19. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

Click here

20. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

Click here

21. REMOVE LUGGAGE COMPARTMENT DOOR COVER

Click here

22. REMOVE SPARE WHEEL COVER

(a) Remove the spare wheel cover.

23. REMOVE REAR FLOOR FINISH PLATE

(a) Remove the 2 clips.

(b) Disengage the 2 clips, 2 claws and 6 guides to remove the rear floor finish plate as shown in the illustration.

Remove in this Direction

24. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

(a) Using a clip remover, remove the clip.

(b) Using a clip remover, remove the clip (A), 5 clips (B) and luggage compartment trim cover assembly LH.

	Clip (A)
	Clip (B)

25. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

(a) Remove the screw.

(b) Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

(1) Disconnect the fuel lid lock control cable sub-assembly.

*A	w/o Fuel Lid Opener Switch
*1	Fuel Lid Lock Control Cable Sub-assembly
*2	Luggage Door Lock Control Cable Sub-assembly

(d) Disconnect the luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

26. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY

(a) Turn back the floor carpet so that the luggage door lock control cable sub-assembly can be removed.

(b) w/o Wireless Door Lock System:

(1) Disconnect the luggage door lock control cable sub-assembly.

(1) Disengage the claw as shown in the illustration.

(2) Disconnect the luggage door lock control cable sub-assembly.

(d) Disengage each clamp and disconnect the luggage door lock control cable sub-assembly.

(e) Disengage each clamp and remove the luggage door lock control cable sub-assembly.