Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001I05W |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [03/2019 - 09/2022] |
Title: DOOR / HATCH: FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback): REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during fuel lid lock control cable sub-assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock*1
|
Power Door Lock Control System
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for TMC Made Gasoline Model:
Click here
for TMMMS Made:
Click here
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click here
for Power Seat:
Click here
2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
3. REMOVE REAR FLOOR MAT ASSEMBLY (w/o Spare Tire)
Click here
4. REMOVE REAR DECK TRIM COVER (w/o Spare Tire)
Click here
5. REMOVE DECK BOARD ASSEMBLY (w/ Spare Tire)
Click here
6. REMOVE DECK FLOOR BOX LH (w/ Spare Tire)
Click here
7. REMOVE DECK FLOOR BOX RH (w/ Spare Tire)
Click here
8. REMOVE REAR NO. 1 FLOOR BOARD (w/ Spare Tire)
Click here
9. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)
Click here
10. REMOVE REAR DECK TRIM COVER (w/ Spare Tire)
Click here
11. REMOVE REAR SEAT ASSEMBLY
Click here
12. REMOVE REAR DOOR SCUFF PLATE LH
Click here
13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
14. REMOVE REAR SEAT SIDE GARNISH LH
Click here
15. REMOVE DECK TRIM SIDE LOWER BOARD LH (w/ Spare Tire)
Click here
16. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Click here
17. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
18. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
19. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
20. REMOVE LAP BELT OUTER ANCHOR COVER
Click here
21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
22. REMOVE CENTER PILLAR LOWER GARNISH LH
Click here
23. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
(b) Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.
|
|
(c) Disconnect the fuel lid lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.
|
|
24. REMOVE FUEL FILLER OPENING LID LOCK RETAINER
(a) Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (A), and then pull the fuel filler opening lid lock retainer.
|
|
(b) Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (B), and then pull the fuel filler opening lid lock retainer.
|
|
(c) Pull out the fuel filler opening lid lock retainer with both the guides (B) and guides (C) aligned with the cutouts as shown in the illustration.
|
|
*a
|
Cutout
|
*b
|
Guide (B)
|
*c
|
Guide (C)
|
|
|
(d) Disengage the 2 claws to remove the fuel filler opening lid lock retainer as shown in the illustration.
|
Remove in this Direction
|
25. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
(a) Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.
(b) Disengage each clamp and remove the fuel lid lock control cable sub-assembly.
|