DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2020 - 2021 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001HZS7
Model Year Start: 2020	Model: GR Corolla	Prod Date Range: [03/2019 - 06/2020]
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2020 - 2021 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 06/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Pre-collision System
Rear door glass sub-assembly Rear door glass run Rear door inner glass weatherstrip	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed
*1: for Hatchback
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision System
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock*1	Power Door Lock Control System (for Hatchback)
Rear door glass sub-assembly Rear door glass run Rear door inner glass weatherstrip	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FKS:

Click here

for 2ZR-FAE:

Click here

for 2ZR-FXE:

Click here

3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

6. REMOVE REAR SPEAKER ASSEMBLY

Click here

7. REMOVE REAR DOOR FRAME GARNISH

Click here

8. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here

9. REMOVE REAR DOOR PANEL PROTECTOR

Click here

10. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

11. REMOVE REAR DOOR GLASS RUN

Click here

12. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disconnect the rear door weatherstrip until the screw of the rear door window division bar sub-assembly is visible.

13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here

14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

15. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

(a) Disconnect the connector.

*a	Release Plate
	Remove in this Direction

(b) Using a T30 "TORX" socket wrench, remove the 3 screws.

(c) Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.

(d) When reusing the rear door lock with motor assembly:

(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.

16. REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE

(a) Using a screwdriver, disengage the claw and open the cover as shown in the illustration.

(b) Remove the rear door lock open lever remote control cable as shown in the illustration.

Remove in this Direction

17. REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE

(a) Using a screwdriver, disengage the 3 claws and open the cover as shown in the illustration.

(b) Remove the rear door inside lock/unlock knob locking cable as shown in the illustration.

Remove in this Direction