| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001HZM7 |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [03/2019 - 09/2022] |
| Title: SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for HV Model) |
|
|
Pre-collision System (for HV Model) |
NOTICE:
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: for Hatchback | |||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for Gasoline Model) |
|
|
Pre-collision System (for Gasoline Model) |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock*1 |
Power Door Lock Control System (for Hatchback, Gasoline Model) |
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
for HV Model:Click here
![2020 MY Corolla Corolla HV [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for TMC Made Gasoline Model:Click here
for TMMMS Made: Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY (for Gasoline Model)
w/o Rear Seat Heater: Click here
4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
w/o Rear Seat Heater: Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
w/o Rear Seat Heater: Click here
6. REMOVE REAR SEAT ASSEMBLY (for Gasoline Model)
w/ Rear Seat Heater: Click here
7. REMOVE FRONT DOOR SCUFF PLATE
Click here
8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
(a) Disconnect the front door opening trim weatherstrip.
9. REMOVE REAR DOOR SCUFF PLATE (for Gasoline Model)
Click here
10. REMOVE REAR DOOR SCUFF PLATE (for HV Model)
Click here
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
(a) Disconnect the rear door opening trim weatherstrip.
12. REMOVE LAP BELT OUTER ANCHOR COVER
|
(a) Disengage the 3 claws to remove the lap belt outer anchor cover. |
|
13. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY
|
(a) Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly. |
|
14. REMOVE CENTER PILLAR LOWER GARNISH
Click here
15. REMOVE CENTER PILLAR UPPER GARNISH
Click here
16. REMOVE FRONT SEAT OUTER BELT ASSEMBLY
|
(a) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly. |
|
|
(b) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector. HINT: Tape the screwdriver tip before use. |
|
|
(c) Remove the 2 bolts. |
|
(d) Disengage the 2 guides to remove the front seat outer belt assembly.
17. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY
|
(a) Remove the 2 bolts. |
|
(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.
|
|