Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HZHU
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [03/2019 - 09/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CURTAIN SHIELD AIRBAG ASSEMBLY (for Sedan): REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Control System

2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for HV Model): INITIALIZATION

Pre-collision System

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

NOTICE:

for HV Model:

  • After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

for Gasoline Model:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for HV Model: Click here 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION

for TMC Made Gasoline Model: Click here 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION 2021 - 2022 MY Corolla Corolla Hatchback GR Corolla [04/2020 - 09/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION

for TMMMS Made: Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): PRECAUTION 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): PRECAUTION

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2ZR-FAE: Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; MAINTENANCE: 2ZR-FAE BATTERY: REMOVAL+

for M20A-FKS: Click here 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL+

for 2ZR-FXE: Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; MAINTENANCE: 2ZR-FXE AUXILIARY BATTERY: REMOVAL+

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2019 - 04/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE ROOF HEADLINING ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 04/2020]; INTERIOR PANELS / TRIM: ROOF HEADLINING (for Sedan): REMOVAL 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022]; INTERIOR PANELS / TRIM: ROOF HEADLINING (for Sedan): REMOVAL

4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

Deployment Side

NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.

(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(c) Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button and disconnect the airbag connector.

*a

Airbag Connector

*b

Airbag Connector Locking Button

*c

Protective Tape

Release in this Direction

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(d) Using a needle nose pliers No. 2 or equivalent, remove the 4 pins from the 3 clips (A) and clip (B).

NOTICE:

Do not damage the pins.

*1

Pin

-

-

*a

Clip (A)

*b

Clip (B)

*c

Clip (C)

*d

Needle Nose Pliers No. 2

*e

Thin Screwdriver

-

-

Remove in this Direction

-

-

(e) Using 2 thin screwdrivers, disengage the 2 claws of each clip (A) and (B), and separate the 3 clips (A) and clip (B) from the vehicle body as shown in the illustration.

HINT:

Separate the 3 clips (A), clip (B) and curtain shield airbag assembly from the vehicle body as a unit.

(f) Disengage the 2 clips (C).

(g) While holding the curtain shield airbag assembly, remove the 7 bolts and curtain shield airbag assembly.

(h) Remove the 3 clips (A) and clip (B) from the curtain shield airbag assembly.