SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT PASSENGER AIRBAG ASSEMBLY: REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001HZHR
Model Year Start: 2020	Model: GR Corolla	Prod Date Range: [03/2019 - 09/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT PASSENGER AIRBAG ASSEMBLY: REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Pre-collision System

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*1: for Hatchback
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision System
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock*1	Power Door Lock Control System

NOTICE:

for HV Model:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

for Gasoline Model:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for HV Model: Click here

for TMC Made Gasoline Model: Click here

for TMMMS Made: Click here

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

Click here

3. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a	White Housing Lock	*b	Yellow CPA
	Push in this Direction		Slide in this Direction

(2) Push down the white housing lock again and disconnect the connector.

(3) Check that the position of the white housing lock is as shown in the illustration.

Correct

Incorrect

4. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

5. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:

When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.

Deployment Side

(a) Remove the 2 screws.

(b) Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.

*a	Passenger Airbag Door Retainer
	Move the screwdriver in this Direction

NOTICE:

Do not damage the deployment surface of the instrument panel passenger airbag assembly.

(c) Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.

6. REMOVE NO. 2 INSTRUMENT PANEL WIRE

(a) Disengage the clamp.

*a	Protective Tape
*b	Airbag Connector
*c	Airbag Connector Locking Button
*d	Vent Hole Connector
*e	Vent Hole Connector Locking Button
	Release in this Direction

(b) Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locking buttons and vent hole connector locking button.

(c) Disconnect the 2 airbag connectors and vent hole connector to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.