Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HZ93 |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 09/2022] |
Title: EC65 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE: ADJUSTMENT; 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022] |
ADJUSTMENT
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly adjustment are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System (for Gasoline Model)
|
|
Pre-collision System (for Gasoline Model)
|
Lighting System (w/ AFS)(EXT)
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
Replacement of ECM*1
|
Code registration (Immobiliser system)
|
Engine start
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
PROCEDURE
1. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
-
Make sure to apply the parking brake and chock a wheel before performing this procedure.
-
If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
4. REMOVE BATTERY
Click here
5. REMOVE CONSOLE BOX ASSEMBLY
Click here
6. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
7. REMOVE RADIATOR SUPPORT OPENING COVER
Click here
8. REMOVE INLET NO. 1 AIR CLEANER
Click here
9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here
11. REMOVE ECM
Click here
12. DISCONNECT ENGINE WIRE
Click here
13. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
14. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY
HINT:
-
After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.
-
If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.
(a) Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.
|
|
(b) Push the 2 claws together at the top of the lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to push up the lock piece.
*a
|
Lock Piece
|
*b
|
Bottom View
|
*c
|
Push
|
*d
|
Push up
|
(c) Connect the transmission control select cable to the floor shift lever assembly and install the clip.
NOTICE:
-
Securely install the end of the floor shift transmission control select cable to the transmission floor shift assembly.
-
Install the end of the floor shift transmission control select cable so that its adjustment lock section is on the driver side.
|
|
(d) Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.
|
|
*1
|
Outer Select Lever
|
*2
|
Reverse Restrict Pin Assembly
|
*a
|
Secured
|
|
|
(e) Push the slider shaft against the cam wall.
NOTICE:
-
Do not pull up the slider shaft.
-
When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.
|
|
*a
|
Slider Shaft
|
*b
|
Cam Wall
|
|
|
(f) Push the lock piece into the adjuster case.
NOTICE:
-
Securely push in the lock piece until the 2 claws are engaged.
-
When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.
|
|
*a
|
Lock Piece
|
*b
|
Adjuster Case
|
*c
|
Push in
|
|
|
(g) Move the shift lever to the reverse position, so that the outer select lever can be released.
|
|
*1
|
Outer Select Lever
|
*2
|
Reverse Restrict Pin Assembly
|
*a
|
Released
|
|
|
15. INSTALL BATTERY CLAMP SUB-ASSEMBLY
Click here
16. CONNECT ENGINE WIRE
Click here
17. INSTALL ECM
Click here
18. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Click here
19. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
20. INSTALL INLET NO. 1 AIR CLEANER
Click here
21. INSTALL RADIATOR SUPPORT OPENING COVER
Click here
22. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
23. INSTALL CONSOLE BOX ASSEMBLY
Click here
24. INSTALL BATTERY
Click here
25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here
|