Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HZ90 |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 09/2022] |
Title: EG60 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE (for TMC Made): REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System (for Gasoline Model)
|
|
Pre-collision System (for Gasoline Model)
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock*1
|
Power Door Lock Control System (for Hatchback, Gasoline Model)
|
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
Gas leak from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
Replacement of ECM*2
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function
|
|
Replacement of ECM*3
|
Code registration (Immobiliser system)
|
Engine start
|
|
CAUTION:
-
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
-
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
PROCEDURE
1. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
-
Make sure to apply the parking brake and chock a wheel before performing this procedure.
-
If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
4. REMOVE BATTERY
Click here
5. REMOVE CONSOLE BOX ASSEMBLY
Click here
6. REMOVE RADIATOR SUPPORT OPENING COVER (for Hatchback)
Click here
7. REMOVE RADIATOR SUPPORT OPENING COVER (w/ Illumination)
Click here
8. REMOVE INLET NO. 1 AIR CLEANER
Click here
9. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
10. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
11. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here
12. REMOVE ECM
Click here
13. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
14. REMOVE FRONT FLOOR COVER LH
Click here
15. REMOVE FRONT FLOOR COVER RH
Click here
16. REMOVE FRONT FLOOR CENTER BRACE
Click here
17. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
Click here
18. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
(a) Remove the 3 nuts and front No. 1 floor heat insulator from the vehicle body.
|
|
19. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.
|
|
*a
|
Transmission Control Select Cable
|
*b
|
Transmission Control Shift Cable
|
|
|
(b) Disconnect the transmission control shift cable from the floor shift shift lever assembly.
(c) Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control select cable from the floor shift lever assembly.
NOTICE:
Do not forcibly pull the transmission control cable assembly into the cabin.
|
|
(d) Disconnect the transmission control shift cable from the floor shift lever assembly in the same manner as the transmission control select cable.
(e) Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.
|
|
(f) Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.
(h) Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.
(i) Remove the 2 nuts and transmission control cable assembly from the vehicle body.
|
|
|