Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HXMR |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 09/2022] |
Title: K313 (CVT): PARK / NEUTRAL POSITION SWITCH: ADJUSTMENT; 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022] |
ADJUSTMENT
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during park/neutral position switch assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System (for Gasoline Model)
|
|
Pre-collision System (for Gasoline Model)
|
Lighting System (w/ AFS)(EXT)
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
Replacement of ECM
|
-
Reset memory
-
Deceleration sensor zero point calibration
-
CVT oil pressure calibration
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
|
Replacement of ECM*1
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function
|
|
Replacement of ECM*2
|
Code registration (Immobiliser system)
|
Engine start
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
PROCEDURE
1. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
-
Make sure to apply the parking brake and chock a wheel before performing this procedure.
-
If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
4. REMOVE RADIATOR SUPPORT OPENING COVER
Click here
5. REMOVE INLET NO. 1 AIR CLEANER
Click here
6. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
7. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here
9. REMOVE ECM
Click here
10. REMOVE BATTERY
Click here
11. DISCONNECT ENGINE WIRE
Click here
12. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
13. ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Loosen the 2 bolts of the park/neutral position switch assembly.
|
|
(b) Align the protrusion with the neutral basic line.
|
|
*a
|
Neutral Basic Line
|
*b
|
Protrusion
|
|
|
(c) Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
14. INSTALL BATTERY CLAMP SUB-ASSEMBLY
Click here
15. CONNECT ENGINE WIRE
Click here
16. INSTALL BATTERY
Click here
17. INSTALL ECM
Click here
18. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Click here
19. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
20. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
21. INSTALL INLET NO. 1 AIR CLEANER
Click here
22. INSTALL RADIATOR SUPPORT OPENING COVER
Click here
23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here
|