Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HU8U
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [03/2019 - 11/2022]
Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: B1543; Extension Module Disconnected 2; 2020 - 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 11/2022]

DTC

B1543

Extension Module Disconnected 2

DESCRIPTION

If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.

HINT:

The Navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the Navigation system will not operate normally.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B1543

Extension Module Disconnected 2

Navigation ECU disconnected

  • Navigation ECU
  • Radio and display receiver assembly
  • Harness or connector

HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.

WIRING DIAGRAM

w/ Manual (SOS) Switch
w/o Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PRECAUTION 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PRECAUTION

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly or navigation ECU may not operate normally.

PROCEDURE

1.

CHECK MAP SCREEN

(a) Turn the ignition switch to ACC and wait for 90 seconds.

(b) Press the "MAP" switch and check that the map screen is displayed normally.

Result

Proceed to

Map screen is displayed normally

A

Map screen is not displayed normally

B

HINT:

  • This DTC may be stored due to environmental reasons such as electrical noise or interference.
  • Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)
A

USE SIMULATION METHOD TO CHECK

B

2.

CHECK DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Turn the ignition switch off.

(c) Turn the ignition switch to ON and wait for 90 seconds.

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

Result

Proceed to

OK

A

NG (w/ Manual (SOS) Switch)

B

NG (w/o Manual (SOS) Switch)

C

A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 7

B

3.

CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)

(a) Disconnect the I69 navigation ECU connector.

*a

Front view of wire harness connector

(to Navigation ECU)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I69-23 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I69-10 (+B) - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

(a) Disconnect the t3 navigation ECU connector.

*a

Front view of wire harness connector

(to Radio and Display Receiver Assembly)

*b

Front view of wire harness connector

(to Navigation ECU)

(b) Disconnect the t5 radio and display receiver assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

t3-4 (US4+) - t5-1 (US4+)

Always

Below 1 Ω

t3-5 (US4-) - t5-2 (US4-)

Always

Below 1 Ω

t3-6 (UGD4) - t5-3 (UGD4)

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

REPLACE NAVIGATION ECU

(a) Replace the navigation ECU with a new one.

Click here 2020 - 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 11/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION ECU: REMOVAL

NEXT

6.

CHECK DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Turn the ignition switch off.

(c) Turn the ignition switch to ON and wait for 90 seconds.

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

7.

CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)

(a) Disconnect the I69 navigation ECU connector.

*a

Front view of wire harness connector

(to Navigation ECU)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I69-23 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I69-10 (+B) - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

(a) Disconnect the s1 navigation ECU connector.

*a

Front view of wire harness connector

(to Radio and Display Receiver Assembly)

*b

Front view of wire harness connector

(to Navigation ECU)

(b) Disconnect the s3 radio and display receiver assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

s1-4 (US4+) - s3-1 (US4+)

Always

Below 1 Ω

s1-5 (US4-) - s3-2 (US4-)

Always

Below 1 Ω

s1-6 (UGD4) - s3-3 (UGD4)

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

9.

REPLACE NAVIGATION ECU

(a) Replace the navigation ECU with a new one.

Click here 2020 - 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 11/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION ECU: REMOVAL

NEXT

10.

CHECK DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Turn the ignition switch off.

(c) Turn the ignition switch to ON and wait for 90 seconds.

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL