Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HTHJ |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [03/2019 - 09/2022] |
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for Gasoline Model): ON-VEHICLE INSPECTION; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [03/2019 - 09/2022] |
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT SPEEDOMETER
NOTICE:
-
The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake actuator assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake actuator assembly) because it is the source of the vehicle speed signal.
-
Data List values of the skid control ECU (brake actuator assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
-
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
(a) Warm up the engine.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Brake / Data List.
(f) Read the Data List according to the display on the Techstream.
Chassis > Brake > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Vehicle Speed
|
Maximum wheel speed sensor
|
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)
|
Vehicle stopped: 0 km/h (0 mph)
|
When driving at constant speed: No large fluctuations
|
Chassis > Brake > Data List
Tester Display
|
Vehicle Speed
|
Reference (for Speedometer with Imperial Units for Main Scale):
Techstream Indication (mph)
|
Acceptable Range (mph)
|
20
|
19.3 to 21.8
|
40
|
39.6 to 42.4
|
60
|
60.0 to 62.8
|
80
|
80.3 to 83.5
|
100
|
100.8 to 104.0
|
120
|
121.3 to 124.5
|
140
|
141.8 to 145.0
|
Reference (for Speedometer with Metric Units for Main Scale):
Techstream Indication (km/h)
|
Acceptable Range (km/h)
|
20
|
18.5 to 22.5
|
40
|
38.8 to 43.3
|
60
|
59.2 to 63.7
|
80
|
79.4 to 84.4
|
100
|
99.9 to 104.9
|
120
|
120.4 to 125.4
|
140
|
140.9 to 145.9
|
160
|
161.3 to 166.3
|
180
|
181.8 to 186.8
|
200
|
202.3 to 207.3
|
220
|
222.8 to 227.8
|
OK:
Speedometer reading is within the acceptable range at each vehicle speed.
2. INSPECT TACHOMETER
(a) Warm up the engine.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus:
-
Powertrain / Engine / Data List. (for M20A-FKS)
-
Powertrain / Engine and ECT / Data List. (for 2ZR-FAE)
(f) Read the Data List according to the display on the Techstream.
(1) for M20A-FKS
Powertrain > Engine > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Engine Speed
|
Engine speed
|
Min.: 0 rpm, Max.: 16383 rpm
|
600 to 700 rpm: Idling (shift lever in P, engine warmed up and A/C off)
|
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
|
Powertrain > Engine > Data List
Tester Display
|
Engine Speed
|
(2) for 2ZR-FAE
Powertrain > Engine and ECT > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Engine Speed
|
Engine speed
|
Min.: 0 rpm, Max.: 16383 rpm
|
710 to 810 rpm: Idling
|
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
|
Powertrain > Engine and ECT > Data List
Tester Display
|
Engine Speed
|
Reference:
Techstream Indication (rpm)
|
Acceptable Range (rpm)
Data in ( ) is for Reference
|
700
|
630 to 770
|
1000
|
(900 to 1100)
|
2000
|
(1850 to 2150)
|
3000
|
2800 to 3200
|
4000
|
(3800 to 4200)
|
5000
|
4800 to 5200
|
6000
|
(5750 to 6250)
|
7000
|
6700 to 7300
|
OK:
Tachometer reading is within the acceptable range at each engine speed.
3. INSTALL WARNING OR INDICATOR LIGHT (INITIAL CHECK)
(a) Turn the ignition switch off.
(b) Turn the ignition switch ON, and check the operation of the warning and indicator lights in the following table.
OK:
All of the lights illuminate and then turn off.
Warning or Indicator Light
|
Brake warning light / red (malfunction)
|
SRS warning light
|
Charge warning light
|
EPS warning light
|
MIL (Check engine warning light)
|
PCS warning light*1
|
Slip indicator light
|
VSC OFF indicator light
|
ABS warning light
|
Brake warning light / yellow (minor malfunction)
|
Tire pressure warning light*2
|
Electric parking brake auto off indicator light*3
|
Eco driving indicator light*4
|
Brake hold standby indicator light*5
|
-
*1: w/ Forward Recognition Camera
-
*2: w/ Tire Pressure Warning System
-
*3: for Manual Transmission with Electric Parking Brake System
-
*4: w/ Eco Driving Indicator
-
*5: w/ Electric Parking Brake System
HINT:
The illumination of each warning light and indicator light varies.
|