Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HTGR |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 03/2023] |
Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P011515; Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open; 2020 - 2023 MY Corolla Corolla Hatchback [03/2019 - 03/2023] |
DTC
|
P011515
|
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open
|
DESCRIPTION
Refer to DTC P011511.
Click here
HINT:
When DTC P011515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P011515
|
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open
|
Diagnosis condition:
Abnormal condition:
-
The engine coolant temperature sensor output voltage is higher than 4.91 V.
Malfunction time:
Trip logic:
Detection conditions:
Sensors/components used for detection:
-
Engine coolant temperature sensor
|
-
Open or short in engine coolant temperature sensor circuit
-
Engine coolant temperature sensor
-
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0118
-
DTC for Mexico Models: Applies
|
HINT:
When this DTC is output, check the engine coolant temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
DTC No.
|
Coolant Temperature
|
Malfunction
|
P011515
|
-40°C (-40°F)
|
-
Short to +B in THW circuit
-
Open in THW circuit
-
Open in ETHW circuit
|
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
Click here
MONITOR DESCRIPTION
When the ignition switch is turned ON and the output voltage of the engine coolant temperature sensor is higher than 4.91 V for 0.5 seconds or more, the ECM determines that the engine coolant temperature sensor circuit is malfunctioning and illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs
|
P0118: Engine coolant temperature sensor range check (high voltage)
|
Required Sensors/Components (Main)
|
Engine coolant temperature sensor
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
0.5 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
All of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
Starter
|
Off
|
TYPICAL MALFUNCTION THRESHOLDS
Engine coolant temperature sensor voltage [Engine coolant temperature]
|
Higher than 4.91 V [Less than -59°C (-74°F)]
|
CONFIRMATION DRIVING PATTERN
Refer to DTC P011511.
Click here
WIRING DIAGRAM
Refer to DTC P011511.
Click here
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK TERMINAL VOLTAGE (ENGINE COOLANT TEMPERATURE SENSOR)
|
*a
|
Front view of wire harness connector
(to Engine Coolant Temperature Sensor)
|
(a) Disconnect the engine coolant temperature sensor connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
C48-2 - Body ground
|
Ignition switch ON
|
0 to 5.5 V
|
OK
|
|
|
2.
|
READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
|
*1
|
Engine Coolant Temperature Sensor
|
*2
|
ECM
|
*a
|
Front view of wire harness connector
(to Engine Coolant Temperature Sensor)
|
-
|
-
|
(a) Disconnect the engine coolant temperature sensor connector.
(b) Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Powertrain > Engine > Data List
Tester Display
|
Coolant Temperature
|
(g) According to the display on the Techstream, read the Data List.
OK:
Techstream Display
|
Specified Condition
|
Coolant Temperature
|
140°C (284°F)
|
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here
NG
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
|
(a) Disconnect the engine coolant temperature sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C48-2 - C76-125 (THW)
|
Always
|
Below 1 Ω
|
C48-1 - C76-124 (ETHW)
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
4.
|
CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
|
(a) Disconnect the engine coolant temperature sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C48-2 or C76-125 (THW) - Other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|