Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HTGJ |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 03/2023] |
Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P010515; Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open; 2020 - 2023 MY Corolla Corolla Hatchback [03/2019 - 03/2023] |
DTC
|
P010515
|
Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open
|
DESCRIPTION
Refer to DTC P010511.
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P010515
|
Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open
|
The manifold absolute pressure sensor output voltage is higher than 4.5 V for 0.5 seconds or more (1 trip detection logic).
|
-
Open or short in manifold absolute pressure sensor circuit
-
Manifold absolute pressure sensor
-
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0108
-
DTC for Mexico Models: Applies
|
HINT:
When this DTC is output, check the intake manifold absolute pressure in the Data List. Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.
DTC No.
|
Intake Manifold Absolute Pressure
|
Malfunction
|
P010515
|
Higher than 130 kPa (18.85 psi)
|
-
Short in VCPM to PIM circuit
-
Open in PIM circuit
-
Open in EPIM circuit
|
If the Data List value is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
Click here
MONITOR DESCRIPTION
The ECM monitors the manifold absolute pressure sensor voltage and uses this value to calculate the intake manifold pressure. When the manifold absolute pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold absolute pressure sensor circuit, illuminates the MIL and stores a DTC.
Example:
If the manifold absolute pressure sensor output voltage is higher than 4.5 V for 0.5 seconds or more, the ECM stores this DTC.
MONITOR STRATEGY
Related DTCs
|
P0108: Manifold absolute pressure sensor range check (high voltage)
|
Required Sensors/Components (Main)
|
Manifold absolute pressure sensor
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
0.5 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
All of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
Time after ignition switch off to ON
|
0.5 seconds or more
|
Time after starter on to off
|
0.5 seconds or more
|
TYPICAL MALFUNCTION THRESHOLDS
Manifold absolute pressure sensor voltage (Manifold absolute pressure)
|
Higher than 4.5 V (Higher than 130 kPa(abs) [19 psi(abs)])
|
CONFIRMATION DRIVING PATTERN
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Start the engine and wait 5 seconds or more [A].
-
Turn the Techstream on.
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P010515.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
WIRING DIAGRAM
Refer to DTC P010511.
Click here
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK HARNESS AND CONNECTOR
|
*a
|
Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
|
HINT:
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
(a) Disconnect the manifold absolute pressure sensor connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
C21-3 (VC) - C21-1 (E2)
|
Ignition switch ON
|
4.75 to 5.25 V
|
C21-2 (PIM) - C21-1 (E2)
|
Ignition switch ON
|
1.2 to 5.25 V
|
(d) Turn the ignition switch off and wait for at least 30 seconds.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C21-1 (E2) - Body ground
|
Ignition switch off
|
Below 1 Ω
|
C21-3 (VC) - C21-2 (PIM)
|
Ignition switch off
|
171 to 189 kΩ
|
NG
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
|
(a) Disconnect the manifold absolute pressure sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C21-1 (E2) - C76-119 (EPIM)
|
Always
|
Below 1 Ω
|
C21-2 (PIM) - C76-120 (PIM)
|
Always
|
Below 1 Ω
|
C21-2 (PIM) or C76-120 (PIM) - Other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|