Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HT5J
Model Year Start: 2020 Model: Corolla Prod Date Range: [03/2019 - 09/2022]
Title: 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P1604; Startability Malfunction; 2020 - 2022 MY Corolla [03/2019 - 09/2022]

DTC

P1604

Startability Malfunction

DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.

Using the Techstream, the conditions present when the DTC was stored can be confirmed by referring to the Freeze Frame Data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No.

Detection Item

DTC Detection Condition

MIL

Memory

Note

P1604

Startability Malfunction

Either of the following conditions is met: (1 trip detection logic):

  • The engine speed is below 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below).
  • After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds.

Does not come on

DTC stored

DTC for Mexico Models

- Applies

Trouble Area

Ignition system

  • Spark plug
  • Ignition coil assembly

Fuel system

  • Fuel injector assembly
  • Fuel pump
  • Fuel pump control circuit
  • Fuel pressure regulator assembly
  • Fuel line
  • Purge VSV system
  • Fuel quality (existence of foreign matter, degradation)

Intake and exhaust systems

  • Mass air flow meter sub-assembly
  • Intake system

    (Air leaks or deposit accumulation)

  • Throttle body assembly
  • Air fuel ratio sensor
  • Heated oxygen sensor
  • Camshaft timing oil control valve assembly
  • VVT system (Variable Valve Timing system)

Other control systems

  • ECM
  • Wire harness or connector
  • Knock sensor
  • Engine coolant temperature sensor

Engine

  • Thermostat
  • Engine assembly

High load from another system

  • Air conditioning system
  • Power steering system
  • Electrical load signal system
  • CVT system

CAUTION / NOTICE / HINT

HINT:

  • DTC P1604
    • In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and Freeze Frame Data when the user mentions problems such as starting difficulty.

      As this DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.

    • As DTCs may be stored when an Active Test or learning is performed, make sure to clear the DTCs before returning the vehicle to the customer.
    • If any other DTCs are output, perform troubleshooting for those DTCs first.
  • DATA LIST / FREEZE FRAME DATA
    • Read Freeze Frame Data using the Techstream. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
    • When confirming the Freeze Frame Data, be sure to check all 5 sets of Freeze Frame Data.

      Click here 2020 MY Corolla [01/2019 - 04/2020]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: FREEZE FRAME DATA 2021 - 2023 MY Corolla [04/2020 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: FREEZE FRAME DATA

    • When confirming the Freeze Frame Data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
    • Try to start the vehicle under the conditions recorded in the Freeze Frame Data which were present when the malfunction occurred. Confirm the data at this time and compare it with the Freeze Frame Data.
    • If the malfunction does not recur, carefully check the vehicle conditions from when the malfunction occurred using Freeze Frame Data.
  • PRECAUTIONS
    • When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
    • If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.

PROCEDURE

1.

CHECK FOR ANY OTHER DTCS OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

(e) Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes

Result

Proceed to

DTC P1604 is output

A

DTC P1604 and other DTCs are output

B

HINT:

  • If any DTCs other than P1604 are output, troubleshoot those DTCs first.
  • Using Freeze Frame Data, confirm the conditions the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.
B

GO TO DTC CHART 2020 MY Corolla [03/2019 - 04/2020]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2021 - 2022 MY Corolla [04/2020 - 09/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART

A

2.

READ FREEZE FRAME DATA (IMMOBILISER COMMUNICATION AND IMMOBILISER FUEL CUT)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Using the Techstream, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Powertrain > Engine and ECT > DTC(P1604) > Freeze Frame Data

Tester Display

Immobiliser Communication

Immobiliser Fuel Cut

OK:

Data List Item

Techstream Display

Immobiliser Communication

ON

Immobiliser Fuel Cut

OFF

HINT:

If the engine is started immediately after reconnecting the battery terminal, the engine may stall immediately after it starts due to the intercommunication process between each ECU. For this reason, when starting the engine after reconnecting the battery terminal, first turn the ignition switch to ON and then wait several seconds for the communication process to complete before starting the engine.

NG

CHECK ENGINE IMMOBILISER SYSTEM

  • w/ Smart Key System: Click here 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING
  • w/o Smart Key System: Click here 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): HOW TO PROCEED WITH TROUBLESHOOTING

OK

3.

READ FREEZE FRAME DATA (ISC LEARNING VALUE)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Using the Techstream, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Powertrain > Engine and ECT > DTC(P1604) > Freeze Frame Data

Tester Display

ISC Learning Value

Freeze Frame Data Item

Result

Suspected Area

Action

Proceed to

ISC Learning Value

Less than 6.2 L/s

-

Go to the next step

A

6.2 L/s or higher

Throttle body assembly

Go to Engine Difficult to Start (from step 15)

B

B

GO TO ENGINE DIFFICULT TO START

A

4.

READ FREEZE FRAME DATA (ENGINE SPEED)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Using the Techstream, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Powertrain > Engine and ECT > DTC(P1604) > Freeze Frame Data

Tester Display

Engine Speed

Freeze Frame Data Item

Result

Suspected Area

Action

Proceed to

Engine Speed

All 5 sets of Freeze Frame Data are 0 rpm (engine did not crank or engine speed was not detected properly)

  • Starter signal circuit
  • Crank position sensor system
  • Battery fully depleted

Go to Engine Difficult to Start (from step 5)

A

100 to 500 rpm (engine cranked but initial combustion did not occur or was delayed)

  • Fuel pump
  • Leaking fuel injector assembly
  • Spark plug
  • Ignition coil assembly

Go to the next step

B

500 rpm or higher (engine speed dropped immediately after initial combustion)

(Low Rev for Eng Start is ON)

  • Spark plug
  • Ignition coil assembly
A

GO TO ENGINE DIFFICULT TO START

B

5.

INTERVIEW THE CUSTOMER

(a) Interview the customer for details about the conditions when the malfunction occurred.

HINT:

If the engine is difficult to start only when the vehicle has been left as is for a long time, a leaking fuel injector assembly is suspected.

Result

Suspected Area

Action

Proceed to

Engine is difficult to start only when the vehicle has been left as is for a long time (1 hour or more)

Leaking fuel injector assembly

Go to Engine Difficult to Start (from step 4)

A

Other than above

  • Fuel pump
  • Spark plug
  • Ignition coil assembly

Go to the next step

B

A

GO TO ENGINE DIFFICULT TO START

B

6.

INTERVIEW THE CUSTOMER

(a) Interview the customer for details about the conditions when the malfunction occurred.

HINT:

If the vehicle is mostly driven for short distances, deposits may have accumulated on the spark plugs, causing starting difficulty.

Result

Suspected Area

Action

Proceed to

Mostly driven short distances

  • Spark plug
  • Ignition coil assembly

Go to Engine Difficult to Start (from step 13)

NEXT

Not mostly driven short distances

  • Fuel pump
  • Spark plug
  • Ignition coil assembly

Go to Engine Difficult to Start (from step 9)

NEXT

GO TO ENGINE DIFFICULT TO START