Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HT55
Model Year Start: 2020 Model: Corolla Prod Date Range: [03/2019 - 11/2022]
Title: 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P0724; Brake Switch "B" Circuit High; 2020 - 2023 MY Corolla [03/2019 - 11/2022]

DTC

P0724

Brake Switch "B" Circuit High

DESCRIPTION

The stop light switch assembly is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch assembly is remaining on. When the stop light switch assembly remains on during "STOP and GO" driving, the ECM interprets this as a fault in the stop light switch assembly. The ECM will illuminate the MIL and store this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P0724

Brake Switch "B" Circuit High

The stop light switch assembly remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic).

  • Short in stop light switch signal circuit
  • Stop light switch assembly
  • ECM

Comes on

DTC stored

DTC for Mexico Models

- Applies

MONITOR DESCRIPTION

This DTC indicates that the stop light switch assembly is remaining on. When the stop light switch assembly remains on during "STOP and GO" driving, the ECM interprets this as a malfunction of the stop light switch assembly. The ECM turns on MIL and stores this DTC. The vehicle must STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) 5 times during 2 driving cycles, in order to detect a malfunction.

MONITOR STRATEGY

Related DTCs

P0724: Brake pedal position switch verify switch input

Required Sensors/Components (Main)

Stop light switch assembly

Required Sensors/Components (Related)

Speed sensor

Frequency of Operation

Continuous

Duration

GO and STOP 5 times

MIL Operation

2 driving cycles

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

All of the following conditions are met

-

Battery voltage

8 V or higher

Ignition switch

ON

Starter

Off

GO: Vehicle speed

30 km/h (18.65 mph) or more

STOP: Vehicle speed

Less than 3 km/h (1.86 mph)

TYPICAL MALFUNCTION THRESHOLDS

Brake pedal position switch

On

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON [A].
  7. Turn the Techstream on.
  8. Wait 5 seconds.
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  10. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0724.
  13. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].
  14. Start the engine [C].
  15. Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  17. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  18. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  19. Input the DTC: P0724.
  20. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
  21. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.

    Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

    HINT:

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.

WIRING DIAGRAM

Refer to DTC P0504.

Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P0504; Brake Switch "A" / "B" Correlation+ 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P0504; Brake Switch "A" / "B" Correlation+

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Using the Techstream, the Data List item "Stop Light Switch" and "ST1" can be read.

    Click here 2020 MY Corolla [03/2019 - 04/2020]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: DATA LIST / ACTIVE TEST 2021 - 2023 MY Corolla [04/2020 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: DATA LIST / ACTIVE TEST

  • Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

Powertrain > Engine and ECT > Data List

Tester Display

Stop Light Switch

(e) Read the values displayed on the Techstream.

OK:

Techstream Display

Measurement Item/Range (display)

Normal Condition

Stop Light Switch

Stop light switch status: ON or OFF

  • ON: Brake pedal depressed
  • OFF: Brake pedal released
OK

CHECK FOR INTERMITTENT PROBLEMS

NG

2.

CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION

(a) Check the stop light switch assembly installation.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; LIGHTING (EXT): STOP LIGHT SWITCH: INSTALLATION .

OK:

Stop light switch assembly is installed correctly.

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

OK

3.

CHECK TERMINAL VOLTAGE (STP VOLTAGE)

*a

Brake Pedal Depressed

*b

Brake Pedal Released

*c

Front view of wire harness connector

(to ECM)

-

-

(a) Disconnect the ECM connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Brake Pedal Operation

Specified Condition

A46-9 (STP) - Body ground

Released

Below 1.5 V

Depressed

7.5 to 14 V

HINT:

If there is a short in the STP terminal circuit, there may be a malfunction in the circuit of a connected ECU.

OK

REPLACE ECM 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (ENGINE CONTROL): ECM: REMOVAL 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): ECM: REMOVAL

NG

4.

CHECK HARNESS AND CONNECTOR

(a) Disconnect the stop light switch assembly connector.

(b) Disconnect the ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A53-3 (L) or A46-9 (STP) - Other terminals

Always

10 kΩ or higher

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR