Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HT48 |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [03/2019 - 11/2022] |
Title: 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P0607; Control Module Performance; 2020 - 2023 MY Corolla [03/2019 - 11/2022] |
DTC
|
P0607
|
Control Module Performance
|
MONITOR DESCRIPTION
The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM functioning properly.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P0607
|
Control Module Performance
|
-
ECM CPUs malfunction
-
Heated oxygen sensor transistor (built into ECM) malfunction
|
-
ECM
-
Heated oxygen sensor
-
Exhaust gas leak
|
Comes on
|
DTC stored
|
DTC for Mexico Models
- Does not apply
|
MONITOR STRATEGY
Related DTCs
|
P0607: Control module performance
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
Heated oxygen sensor
|
Frequency of Operation
|
Continuous
|
Duration
|
60 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
Both of the following conditions are met
|
-
|
Engine
|
Running
|
Estimated heated oxygen sensor temperature
|
450°C (842°F) or higher, and less than 750°C (1382°F)
|
TYPICAL MALFUNCTION THRESHOLDS
Heated oxygen sensor transistors
|
Fail
|
CONFIRMATION DRIVING PATTERN
-
Stop the engine for 30 minutes or more [A].
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON [B].
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Turn the ignition switch to ON [C].
-
Turn the Techstream on.
-
Start the engine and wait 2 minutes [D].
-
Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [E].
-
Idle the engine for 1 minute [F].
-
Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
-
Drive the vehicle at 56 to 80 km/h (35 to 50 mph) for 5 minutes or more [H].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
-
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
-
Input the DTC: P0607, P0136, P0137 or P0138.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
N/A
|
-
Unable to perform DTC judgment
-
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
|
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [I] again.
-
If no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click here
HINT:
-
If a permanent DTC is output, the system is malfunctioning.
-
If no permanent DTC is output, the system is normal.
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK FOR ANY OTHER DTCS OUTPUT
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
|
Proceed to
|
DTC P0607 and P0136, P0137 or P0138 are output
|
A
|
DTC P0607 is output
|
B
|
A
|
|
|
2.
|
INSPECT DTC (P0136, P0137 OR P0138)
|
(a) Refer to the DTC P0136, P0137 or P0138 flowchart.
HINT:
-
If DTC P0136, P0137 or P0138 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".
Click here
-
If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).
3.
|
CHECK FOR EXHAUST GAS LEAK
|
(a) Allow the engine to idle and then rev the engine.
(b) Check for exhaust gas leaks around the heated oxygen sensor.
If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".
HINT:
-
If no exhaust gas leaks are present, there may be a malfunction in the heated oxygen sensor circuit.
-
If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.
-
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click here
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
(e) Turn the ignition switch off.
NEXT
|
|
|
5.
|
PERFORM CONFIRMATION DRIVING PATTERN
|
(a) Start the engine.
(b) Turn the Techstream on.
(c) Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or higher.
(d) Perform the driving pattern.
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
(1) Accelerate the vehicle until 80 km/h (50 mph) and stop the vehicle.
(2) Drive the vehicle between 60 to 80 km/h (37 to 50 mph) for 5 minutes.
(e) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(f) Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
|
Proceed to
|
DTC P0607 and P0136, P0137 or P0138 are output
|
A
|
DTC P0607 is output
|
B
|
DTCs are not output
|
C
|
A
|
|
|
6.
|
INSPECT DTC (P0136, P0137 OR P0138)
|
(a) Refer to the DTC P0136, P0137 or P0138 flowchart.
HINT:
-
If DTC P0136, P0137 or P0138 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".
Click here
-
If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
(e) Turn the ignition switch off.
NEXT
|
|
|
(a) Stop the engine and wait for 30 minutes.
(b) Start the engine and allow it to idle for 2 minutes.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTC P0607 is output
|
B
|
A |
|
END
|
|