Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HT37 |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [03/2019 - 11/2022] |
Title: 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P0196; Engine Oil Temperature Sensor (Range/Performance); 2020 - 2023 MY Corolla [03/2019 - 11/2022] |
DTC
|
P0196
|
Engine Oil Temperature Sensor (Range/Performance)
|
DESCRIPTION
Refer to DTC P0196.
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P0196
|
Engine Oil Temperature Sensor (Range/Performance)
|
Ether of the following conditions is met (2 trip detection logic):
-
The difference between the engine oil temperature and engine coolant temperature is 25°C (45°F) or higher when 7 hours or more have elapsed after the engine was stopped.
-
The difference between the engine oil temperature and intake air temperature is 25°C (45°F) or higher when 7 hours or more have elapsed after the engine was stopped.
|
Engine oil temperature sensor
|
Comes on
|
DTC stored
|
DTC for Mexico Models
- Does not apply
|
MONITOR DESCRIPTION
The ECM uses the engine oil temperature sensor voltage to calculate the engine oil temperature. If the ECM detects that the output from the sensor deviates from the standard range, the ECM determines that the engine oil temperature sensor has malfunctioned and stores DTC P0196.
MONITOR STRATEGY
Related DTCs
|
P0196: Engine oil temperature sensor rationality
|
Required Sensors/Components (Main)
|
Engine oil temperature sensor
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Once per driving cycle
|
Duration
|
-
|
MIL Operation
|
2 driving cycles
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
All of the following conditions are met
|
-
|
Battery voltage
|
10.5 V or higher
|
Engine
|
Running
|
Engine coolant temperature before engine start
|
-10°C (14°F) or higher
|
Soak time
|
7 hours or more
|
Engine coolant temperature sensor circuit fail (P0115, P0116, P0117, P0118, P011B)
|
Not detected
|
Intake air temperature sensor circuit fail (P0111, P0112, P0113, P011B)
|
Not detected
|
Engine oil temperature sensor circuit fail (P0197, P0198)
|
Not detected
|
Soak timer fail (P2610)
|
Not detected
|
TYPICAL MALFUNCTION THRESHOLDS
Both of the following conditions are met
|
-
|
Difference between engine oil temperature and engine coolant temperature
|
25°C (45°F) or higher
|
Difference between engine oil temperature and intake air temperature
|
25°C (45°F) or higher
|
COMPONENT OPERATING RANGE
Engine oil temperature
|
Engine oil temperature sensor value changes in accordance with actual engine oil temperature
|
CONFIRMATION DRIVING PATTERN
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off.
-
With the engine stopped, leave the vehicle as is for 7 hours or more [A].
-
Turn the ignition switch to ON [B].
-
Turn the Techstream on.
-
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
-
Check that the coolant temperature is -10°C (14°F or higher).
-
Start the engine [C].
-
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
-
Input the DTC: P0196.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
N/A
|
-
Unable to perform DTC judgment
-
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
|
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].
-
Turn the ignition switch off.
-
Turn the ignition switch to ON [E].
-
Turn the Techstream on.
-
Start the engine [F].
-
Wait 3 minutes or more.
-
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Check the DTC judgment result again.
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click here
HINT:
-
If a permanent DTC is output, the system is malfunctioning.
-
If no permanent DTC is output, the system is normal.
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0196)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
|
Proceed to
|
DTC P0196 and other DTCs are output
|
A
|
DTC P0196 is output
|
B
|
HINT:
If any DTCs other than P0196 are output, troubleshoot those DTCs first.
|