M20A-FKS (ENGINE CONTROL): CAMSHAFT TIMING CONTROL MOTOR: REMOVAL; 2020 MY Corolla Corolla Hatchback [03/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001HSA9
Model Year Start: 2020	Model: Corolla Hatchback	Prod Date Range: [03/2019 - 09/2019]
Title: M20A-FKS (ENGINE CONTROL): CAMSHAFT TIMING CONTROL MOTOR: REMOVAL; 2020 MY Corolla Corolla Hatchback [03/2019 - 09/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cam timing control motor with EDU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
1: for Hatchback 2: w/ Smart Key System *3: w/o Smart Key System
Battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane Control System (for Gasoline Model)
		Pre-collision System (for Gasoline Model)
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock*1	Power Door Lock Control System (for Hatchback, Gasoline Model)
Replacement of cam timing control motor with EDU assembly Removal and installation of a cam timing control motor with EDU assembly	Inspection after repair	Poor idle, etc. Engine start function, etc.
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
	ECU communication ID registration (Immobiliser system)	Engine start function
	Perform reset memory CVT oil pressure calibration Perform road test to allow TCM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization for Registration
Replacement of ECM*2	Code registration (Smart Key System (for Gasoline Model, Start Function))	Wireless Door Lock Control System (for Gasoline Model with Smart Key System) Smart Key System (for Gasoline Model, Entry Function) Smart Key System (for Gasoline Model, Start Function) Steering lock function
Replacement of ECM*3	Code registration (Immobiliser system)	Engine start

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here

PROCEDURE

1. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Click here

2. REMOVE REAR ENGINE UNDER COVER RH

Click here

3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here

4. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Click here

5. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

for CVT
Click here
for Manual Transaxle
Click here

6. REMOVE ECM

Click here

7. REMOVE BATTERY

Click here

8. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here

9. REMOVE FUEL DELIVERY GUARD

Click here

10. INSTALL ENGINE HANGER

Click here

11. INSTALL ENGINE SUPPORT BRIDGE

for CVT
Click here
for Manual Transaxle
Click here

12. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

(a) Disconnect the air conditioner pressure sensor connector.

(b) Remove the bolt.

(d) Remove the bolt and disengage the clamp to remove the No. 1 cooler refrigerant hose bracket from the engine mounting insulator sub-assembly RH.

(e) Remove the bolt and separate the No. 2 earth wire from the engine mounting insulator sub-assembly RH.

*A	Type A
*B	Type B

(f) Remove the 4 bolts, 2 nuts and engine mounting insulator sub-assembly RH from the vehicle body and engine mounting bracket RH.

HINT:

As the engine mounting insulator sub-assembly RH contacts the air conditioning tube assembly and cannot be taken out, move the engine mounting insulator sub-assembly RH to a position where the bolt of the cam timing control motor with EDU assembly can be removed.

*A	Type A
*B	Type B

13. REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

(a) Disconnect the cam timing control motor with EDU assembly connector.

(b) Remove the 3 bolts and cam timing control motor with EDU assembly from the No. 2 timing chain cover assembly.

NOTICE:

If the cam timing control motor with EDU assembly has been struck or dropped, replace it.

14. REMOVE CAM TIMING CONTROL MOTOR O-RING

(a) Remove the cam timing control motor O-ring from the No. 2 timing chain cover assembly.