Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001HS86
Model Year Start: 2020 Model: Corolla Prod Date Range: [03/2019 - 09/2022]
Title: 2ZR-FAE (FUEL): FUEL TANK (w/ Canister Pump Module): REMOVAL; 2020 - 2022 MY Corolla [03/2019 - 09/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Control System (for Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System (for Gasoline Model)

Lighting System (w/ AFS)(EXT)

Gas leak from exhaust system is repaired

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc.

2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

CAUTION:

  • Never perform work on fuel system components near any possible ignition sources.
  • Vaporized fuel could ignite, resulting in a serious accident.
  • Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
  • The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

PROCEDURE

1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (FUEL): FUEL PUMP (w/ Canister Pump Module): REMOVAL

2. DRAIN FUEL

3. REMOVE TAIL EXHAUST PIPE ASSEMBLY

Click here 2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (INTAKE / EXHAUST): EXHAUST PIPE: REMOVAL

4. REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)

Click here 2020 - 2021 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2020]; REAR SUSPENSION: REAR STABILIZER BAR (for Sedan): REMOVAL+ 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2020 - 09/2022]; REAR SUSPENSION: REAR STABILIZER BAR (for Sedan): REMOVAL+

5. REMOVE REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)

Click here 2020 - 2021 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2020]; REAR SUSPENSION: REAR STABILIZER BAR (for Sedan): REMOVAL+ 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2020 - 09/2022]; REAR SUSPENSION: REAR STABILIZER BAR (for Sedan): REMOVAL+

6. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

(a) Remove the nut, 4 clips and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.

7. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

(a) Disconnect the fuel tank vent hose sub-assembly from the canister (charcoal canister assembly).

Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (FUEL): FUEL SYSTEM: PRECAUTION

*A

for TMC Made

*B

for TMMMS Made

8. DISCONNECT FUEL TANK FILLER PIPE ASSEMBLY

(a) Disconnect the fuel tank filler pipe assembly from the fuel tank assembly.

Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (FUEL): FUEL SYSTEM: PRECAUTION

9. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

(a) Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click here 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (FUEL): FUEL SYSTEM: PRECAUTION

*A

for TMC Made

*B

for TMMMS Made

10. REMOVE FUEL TANK ASSEMBLY

CAUTION:

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

(a) Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.

(b) Remove the 4 bolts, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH.

(c) Lower the engine lifter to remove the fuel tank assembly.

NOTICE:

  • Be careful not to drop the fuel tank assembly.
  • When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.

11. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

(a) Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.

12. REMOVE FUEL TANK VENT HOSE SUB-ASSEMBLY

(a) Disengage the clamp to remove the fuel tank vent hose sub-assembly from the fuel tank assembly.

13. REMOVE NO. 2 FUEL TANK CUSHION

(a) Remove the 2 No. 2 fuel tank cushions from the fuel tank assembly.