Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HS36 |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [03/2019 - 09/2022] |
Title: K120 / K121 (CVT): TRANSMISSION CONTROL CABLE (for TMMMS Made): REMOVAL; 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during floor shift transmission control select cable removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure
|
Necessary Procedure
|
Effect/Inoperative when not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System (for Gasoline Model)
|
|
Pre-collision System (for Gasoline Model)
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock*1
|
Power Door Lock Control System (for Hatchback, Gasoline Model)
|
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
-
Perform reset memory
-
CVT oil pressure calibration
-
Perform road test to allow TCM to learn
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
for Initialization
for Registration
|
Replacement of ECM*3
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function
|
|
Replacement of ECM*2
|
Code registration (Immobiliser system)
|
Engine start
|
|
Gas leak from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
PROCEDURE
1. REMOVE BATTERY
Click here
2. REMOVE ECM
Click here
3. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
4. REMOVE FRONT FLOOR COVER LH (w/ Cover)
Click here
5. REMOVE FRONT FLOOR COVER RH (w/ Cover)
Click here
6. REMOVE FRONT FLOOR CENTER BRACE
Click here
7. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
Click here
8. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
(a) Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.
|
|
9. REMOVE CONSOLE BOX ASSEMBLY
Click here
10. REMOVE FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE
(a) Move the shift lever to N.
(b) Disconnect the floor shift transmission control select cable from the transmission floor shift assembly.
|
Disconnect in this Direction
|
(c) Using a screwdriver, pull out the stopper of the floor shift transmission control select cable.
NOTICE:
Do not remove the stopper. If it is removed, reinstall it to its original position.
|
|
(d) Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the floor shift transmission control select cable from the transmission floor shift assembly.
*a
|
Stopper
|
*b
|
Nut
|
|
Disconnect in this Direction
|
NOTICE:
-
Do not rotate the nut excessively as the interior spring may come off and the floor shift transmission control select cable will not be reusable.
-
Do not forcibly pull the floor shift transmission control select cable into the cabin.
(e) While disengaging the clip as shown in the illustration, disconnect the floor shift transmission control select cable from the transmission control shaft lever together with the clip.
|
|
(f) Remove the clip and disconnect the floor shift transmission control select cable from the No. 1 transmission control cable bracket.
|
|
(g) Remove the nut and disconnect the floor shift transmission control select cable from the vehicle body.
|
|
(h) Remove the 2 nuts and floor shift transmission control select cable from the vehicle body.
|
|
|