| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001HS33 |
| Model Year Start: 2020 | Model: Corolla Hatchback | Prod Date Range: [03/2019 - 03/2023] |
| Title: K120 / K121 (CVT): TRANSMISSION CONTROL CABLE (for TMMMS Made): ADJUSTMENT; 2020 - 2023 MY Corolla Corolla Hatchback [03/2019 - 03/2023] | ||
ADJUSTMENT
PROCEDURE
1. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
- Make sure to apply the parking brake and chock a wheel before performing this procedure.
- If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
2. REMOVE CONSOLE BOX ASSEMBLY
Click here
![2020 - 2022 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 09/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (except G16E-GTS): REMOVAL](/t3Portal/stylegraphics/info.gif)
3. ADJUST SHIFT LEVER POSITION
NOTICE:
Before adjusting the floor shift transmission control select cable, check that the park/neutral position switch assembly and shift lever are in N.
(a) Disconnect the floor shift transmission control select cable from the transmission floor shift assembly.
|
Disconnect in this Direction |
|
(b) Using a screwdriver, pull out the stopper of the floor shift transmission control select cable. NOTICE: Do not remove the stopper. If it is removed, reinstall it to its original position. |
|
(c) Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the floor shift transmission control select cable from the transmission floor shift assembly.
|
*a |
Stopper |
|
*b |
Nut |
|
|
Disconnect in this Direction |
NOTICE:
- Do not rotate the nut excessively as the interior spring may come off and the floor shift transmission control select cable will not be reusable.
- Do not forcibly pull the floor shift transmission control select cable into the cabin.
(d) Push the 2 claws together at the top of the lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to push up the lock piece.
|
*a |
Lock Piece |
*b |
Bottom View |
|
*c |
Push |
*d |
Push up |
(e) Turn the nut of the floor shift transmission control select cable 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.
|
*a |
Stopper |
*b |
Nut |
|
*c |
Push in |
- |
- |
(f) Connect the floor shift transmission control select cable to the transmission floor shift assembly. Check that the spring is positioned at "A" and push in the stopper.
|
*1 |
Transmission Floor Shift Assembly |
- |
- |
|
*a |
Stopper |
*b |
Spring |
|
*c |
Nut |
*d |
Push in |
|
|
Connect in this Direction |
- |
- |
NOTICE:
- If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.
- Make sure that the floor shift transmission control select cable is securely locked.
- Do not forcibly pull the floor shift transmission control select cable into the cabin.
(g) Connect the floor shift transmission control select cable to the transmission floor shift assembly.
|
*a |
Lock Piece |
|
|
Connect in this Direction |
NOTICE:
- Connect the floor shift transmission control select cable all the way to the base of the pin.
- Connect the floor shift transmission control select cable so that its adjustment lock section is on the driver side.
- Check that the lock piece is pulled up.
(h) Push in the lock piece of the adjuster case to lock it.
|
*a |
Lock Piece |
|
*b |
Adjuster Case |
|
*c |
Push in |
NOTICE:
-
When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.
*1
Floor Shift Transmission Control Select Cable
*a
Lever Shaft
- When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or floor shift transmission control select cable forward or backward.
4. INSTALL CONSOLE BOX ASSEMBLY
Click here
|
|