Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HS0H |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [03/2019 - 06/2021] |
Title: LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model without AFS): DATA LIST / ACTIVE TEST; 2020 - 2021 MY Corolla Corolla Hatchback GR Corolla [03/2019 - 06/2021] |
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus:
(1) for Main Body: Body Electrical / Main Body / Data List.
(2) for Steering Angle Sensor: Chassis / Steering Angle Sensor / Data List.
(3) for Combination Meter: Body Electrical / Combination Meter / Data List.
(4) for Front Recognition Camera (Front Lighting Control): Body Electrical / Front Recognition Camera (Front Lighting Control) / Data List.
(5) for Front Recognition Camera: Chassis / Front Recognition Camera / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Parking Brake SW
|
Parking brake switch signal
|
OFF or ON
|
OFF: Parking brake switch off
ON: Parking brake switch on
|
w/o Electric Parking Brake System
|
Auto High Beam Main Switch
|
Auto high beam switch signal
|
OFF or ON
|
OFF: Auto high beam switch not pressed
ON: Auto high beam switch pressed
|
w/ Automatic High Beam System
|
Head Light SW (Head)
|
Light control switch head position signal
|
OFF or ON
|
OFF: Light control switch not in head position
ON: Light control switch in head position
|
-
|
Insolation Amount of Solar Sensor RH
|
Solar sensor RH condition
|
0 to 51100 or SensorFail
|
Condition can be displayed
|
-
|
Insolation Amount of Solar Sensor LH
|
Solar sensor LH condition
|
0 to 51100 or SensorFail
|
Condition can be displayed
|
-
|
Light Sensor Illuminance
|
Light control sensor illuminance
|
0 to 8191 lx or SensorFail
|
Value is output according to ambient light level
|
The displayed value is "0" when no light is detected.
|
AUTO Light Status
|
Auto light control operation status
|
Not AUTO or AUTO
|
Not AUTO: Automatic light control not operating
AUTO: Automatic light control operating
|
-
|
AFS/AHS ECU High Beam Control
|
AFS (adaptive front-lighting system) or adaptive high beam system control function
|
Not Apply or Apply
|
Not Apply: AFS (adaptive front-lighting system) or adaptive high beam system control unavailable
Apply: AFS (adaptive front-lighting system) or adaptive high beam system control valid
|
-
|
AFS/AHS ECU High Beam Light Status
|
AFS (adaptive front-lighting system) or adaptive high beam system high beam operation status
|
OFF or ON
|
OFF: AFS (adaptive front-lighting system) or adaptive high beam system high beam off
ON: AFS (adaptive front-lighting system) or adaptive high beam system high beam on
|
-
|
Light Sensor Connection Status
|
Light control sensor connection status
|
OFF or ON
|
OFF: Automatic light control sensor has not been connected
ON: Automatic light control sensor connected or has been connected
|
-
|
Headlight Lighting Function
|
ECU which controls the lighting system
|
Main Body or Lighting Sys ECU
|
Main Body: Lighting system controlled by main body ECU (multiplex network body ECU)
Lighting Sys ECU: Lighting system is controlled by headlight ECU sub-assembly
|
-
|
Sensitivity
|
Sensitivity of the automatic light control system
|
Light2, Light1, Normal, Dark1 or Dark2
|
Customize setting displayed
|
w/ Automatic Light Control
|
DRL Function
|
Setting of the DRL function on/off
|
OFF or ON
|
Customize setting displayed
|
for vehicles with customize setting "DRL Function"
|
Headlight in Conjunction with Wiper
|
Wiper-linked low beam headlight control
|
OFF or ON
|
Customize setting displayed
|
-
|
Disp Ex ON Sen
|
Ambient brightness level required to dim display lights (combination meter, navigation display, etc.)
|
Light2, Light1, Normal, Dark1 or Dark2
|
Customize setting displayed
|
w/ Automatic Light Control
|
Disp Ex OFF Sen
|
Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.)
|
Light2, Light1, Normal, Dark1 or Dark2
|
Customize setting displayed
|
w/ Automatic Light Control
|
Light Auto OFF Delay
|
Light auto OFF delay
|
Off, 30 s, 60 s or 90 s
|
Customize setting displayed
|
-
|
Auto H Beam STS0
|
Automatic high beam sensor current state
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
If the value of this item is not as specified, the automatic high beam sensor system may be malfunctioning.
-
w/ Automatic High Beam System
|
Auto H Beam STS1
|
Automatic high beam sensor state past 1
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Auto H Beam STS2
|
Automatic high beam sensor state past 2
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Auto H Beam STS3
|
Automatic high beam sensor state past 3
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Auto H Beam STS4
|
Automatic high beam sensor state past 4
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Auto H Beam STS5
|
Automatic high beam sensor state past 5
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Auto H Beam STS6
|
Automatic high beam sensor state past 6
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Auto H Beam STS7
|
Automatic high beam sensor state past 7
|
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err
|
Condition can be displayed*
|
-
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
-
w/ Automatic High Beam System
|
Tail Remind Buzzer Function
|
Setting of the tail remind buzzer function on/off
|
OFF or ON
|
Customize setting displayed
|
-
|
The Number of DTC
|
Number of trouble codes
|
0 to 255
|
Number of stored DTCs displayed
|
-
|
HINT:
*: The details of each value of the Range are as follows:
Display Value
|
Condition
|
Control Condition
|
Diagnostic Note
|
Undetec
|
Automatic high beam sensor being initialized
|
Control suspended (low beam headlights illuminated)
|
-
|
CAM NA
|
Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc.
|
Control suspended (previous beam setting maintained)
|
-
|
No sens
|
No lights detected
|
High beam headlights illuminated
|
Only when vehicle speed within operation speed range
|
Hlight
|
Headlights of oncoming vehicle, etc. detected
|
Low beam headlights illuminated
|
Only when vehicle speed within operation speed range
|
Taillgt
|
Taillights preceding vehicle, etc. detected
|
Low beam headlights illuminated
|
Only when vehicle speed within operation speed range
|
Speed
|
No lights detected and vehicle speed below operation speed
|
Low beam headlights illuminated
|
-
|
Daytime
|
Bright light detected
|
Low beam headlights illuminated
|
-
|
Village
|
Streetlights, etc. detected
|
Low beam headlights illuminated
|
Only when vehicle speed within operation speed range
|
Delay
|
Changing between low beams and high beams
|
Changing between low beams and high beams
|
Only when vehicle speed within operation speed range
|
SAE Mod
|
Not applicable
|
-
|
-
|
Malfunc
|
Aim Lmt
|
Undefin
|
LIN Err
|
Chassis > Steering Angle Sensor > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Light OFF Switch
|
Light control switch DRL OFF*1 or off*2 position signal
|
OFF or ON
|
OFF: Light control switch not in DRL OFF*1 or off*2 position
ON: Light control switch in DRL OFF*1 or off*2 position
|
-
|
Auto Light Switch
|
Light control switch AUTO*3 or DRL*4 position signal
|
OFF or ON
|
OFF: Light control switch not in AUTO*3 or DRL*4 position
ON: Light control switch in AUTO*3 or DRL*4 position
|
-
|
Head Light Switch (Tail)
|
Light control switch tail position signal
|
OFF or ON
|
OFF: Light control switch in neither tail nor head position
ON: Light control switch in tail or head position
|
-
|
Head Light Switch (Head)
|
Light control switch head position signal
|
OFF or ON
|
OFF: Light control switch not in head position
ON: Light control switch in head position
|
-
|
High Beam Main Switch
|
Dimmer switch high position signal
|
OFF or ON
|
OFF: Dimmer switch not in high position
ON: Dimmer switch in high position
|
-
|
Passing Light Switch
|
Dimmer switch high flash position (pass) signal
|
OFF or ON
|
OFF: Dimmer switch not in high flash position
ON: Dimmer switch in high flash position
|
-
|
Auto High Beam Main Switch
|
Auto high beam switch signal
|
OFF or ON
|
OFF: Auto high beam switch off
ON: Auto high beam switch on
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
Turn Signal Switch (Right)
|
Turn signal switch (right turn position) signal
|
OFF or ON
|
OFF: Turn signal switch not in right turn position
ON: Turn signal switch in right turn position
|
-
|
Turn Signal Switch (Left)
|
Turn signal switch (left turn position) signal
|
OFF or ON
|
OFF: Turn signal switch not in left turn position
ON: Turn signal switch in left turn position
|
-
|
Cornering Light/Front Side Illuminate Light Switch
|
Turn signal switch (full turn) signal
|
OFF or ON
|
OFF: Turn signal switch not in left or right turn position
ON: Turn signal switch in left or right full turn position
|
-
|
Front Fog Light Switch
|
Front fog light switch signal
|
OFF or ON
|
OFF: Front fog light switch off
ON: Front fog light switch on
|
w/ Front Fog Light
|
Rear Fog Light/Bad Weather Switch
|
Rear fog light switch signal
|
OFF or ON
|
OFF: Rear fog light switch off
ON: Rear fog light switch on
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
Automatic Light Equipped Info
|
Automatic light control system specification information
|
Unknown, With or Without
|
Unknown: Specification not stored
With: Automatic light control system equipped
Without: Automatic light control system not equipped
|
-
|
Bad Weather Mode Equipped Info
|
Bad weather specification information
|
Unknown, Without or With
|
Unknown: Specification not stored
Without: Bad weather specification not equipped
With: Bad weather specification equipped
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
The Number of DTCs
|
Number of trouble codes
|
0 to 255
|
Number of stored DTCs displayed
|
-
|
-
*1: w/ DRL OFF Switch
-
*2: w/o DRL OFF Switch
-
*3: w/ Automatic Light Control
-
*4: w/o Automatic Light Control
Body Electrical > Combination Meter > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Turn Signal Switch (Left)
|
Turn signal switch (left) signal
|
OFF or ON
|
OFF: Turn signal switch not in left turn position
ON: Turn signal switch in left turn position
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
Turn Signal Switch (Right)
|
Turn signal switch (right) signal
|
OFF or ON
|
OFF: Turn signal switch not in right turn position
ON: Turn signal switch in right turn position
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
Turn Switch Signal (Full Turn)
|
Turn signal switch (full turn) signal
|
OFF or ON
|
OFF: Turn signal switch not in left or right turn position
ON: Turn signal switch in left or right turn position
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
Hazard Flasher Switch
|
Hazard warning signal switch signal
|
OFF or ON
|
OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on
|
-
|
Lane Change Flashing Times Adjust
|
Condition of the lane change flashing times
|
OFF, 3, 4, 5, 6 or 7
|
Customize setting displayed
|
-
|
Body Electrical > Front Recognition Camera (Front Lighting Control) > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Total Distance Traveled
|
Actual driven distance
|
0 to 16777215
|
Roughly the same as the actual driven distance
|
w/ Automatic High Beam System
|
Total Distance Traveled - Unit
|
Actual driven distance unit
|
km or mile
|
Displays the current actual driven distance unit
|
w/ Automatic High Beam System
|
AHB/AHS Information
|
Automatic high beam system or adaptive high beam system specification information
|
Unknown, AHB or AHS
|
Unknown: Specification not stored
AHB: w/ Automatic High Beam System
AHS: w/ Adaptive High Beam System
|
w/ Automatic High Beam System
|
Chassis > Front Recognition Camera > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Front Recognition Camera High Temperature 2
|
Forward recognition camera condition
|
Not High Temperature or High Temperature
|
Not High Temperature: 65°C (149°F) or lower
High Temperature: 65°C (149°F) or higher
|
-
When "High Temperature" is displayed, the automatic high beam system is temporarily suspended.
-
w/ Automatic High Beam System
|
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus:
(1) for Main Body: Body Electrical / Main Body / Active Test.
(2) for Combination Meter: Body Electrical / Combination Meter / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
Tester Display
|
Measurement Item
|
Control Range
|
Diagnostic Note
|
Daytime Running Light
|
Daytime running lights
|
OFF or ON
|
-
|
Taillight Relay
|
Taillight relay
|
OFF or ON
|
-
|
Headlight Relay
|
Low beam headlights
|
OFF or ON
|
-
|
Head Light Hi
|
High beam headlights
|
OFF or ON
|
-
|
Front Fog Light Relay
|
Front fog lights
|
OFF or ON
|
-
w/ Front Fog Light
-
Light control switch in tail position
|
Rear Fog Light Relay
|
Rear fog lights
|
OFF or ON
|
Although the item is displayed on the Techstream, it is not applicable to this vehicle.
|
Dimmer Signal
|
Dimmer signal
|
OFF or ON
|
State where circumference illumination is bright
|
Automatic High Beam Switch Light
|
Auto high beam switch indicator light
|
OFF or ON
|
w/ Automatic High Beam System
|
Body Electrical > Combination Meter > Active Test
Tester Display
|
Measurement Item
|
Control Range
|
Diagnostic Note
|
Multi Display All (White)
|
Multi-information display (White display)
|
OFF or ON
|
-
|
Automatic High Beam Indicator (Green)
|
Automatic high beam indicator light
|
OFF or ON
|
w/ Automatic High Beam System
|
|