Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HI6G
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [01/2019 - 03/2019]
Title: BRAKE SYSTEM (OTHER): BRAKE PEDAL (for Gasoline Model): REMOVAL; 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake pedal support assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: for Hatchback

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System (for Hatchback)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; METER / GAUGE / DISPLAY: HEADUP DISPLAY: REMOVAL

2. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/o Headup Display)

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: KNEE AIRBAG ASSEMBLY: REMOVAL

3. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

Click here 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 09/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (except G16E-GTS): REMOVAL+

4. REMOVE NO. 1 AIR DUCT

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: REMOVAL+

5. REMOVE STOP LIGHT SWITCH ASSEMBLY

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; LIGHTING (EXT): STOP LIGHT SWITCH: REMOVAL+

6. REMOVE BRAKE PEDAL RETURN SPRING

(a) Remove the brake pedal return spring from the brake pedal support assembly and push rod pin.

7. REMOVE PUSH ROD PIN

(a) Remove the clip and push rod pin to separate the brake pedal support assembly from the brake master cylinder push rod clevis.

8. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

(a) Disengage the clamp to separate the wire harness from the brake pedal support assembly.

(b) Remove the bolt and separate the brake pedal support assembly from the instrument panel reinforcement assembly.

(c) Remove the 2 clips.

Nut

Clip

(d) Remove the 4 nuts and brake pedal support assembly.

(e) Remove the nut from the brake pedal support assembly.

9. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

(a) Disengage the 2 claws and remove the stop light switch mounting adjuster.

10. REMOVE BRAKE PEDAL PAD

(a) Remove the brake pedal pad from the brake pedal support assembly.