Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HHPY |
Model Year Start: 2020 |
Model: Corolla Hatchback |
Prod Date Range: [01/2019 -
] |
Title: K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: P274912,P274914,P274931; Intermediate Shaft Speed Sensor "C" Circuit Short to Battery; 2020 - 2025 MY Corolla Corolla Hatchback [01/2019 - ] |
DTC
|
P274912
|
Intermediate Shaft Speed Sensor "C" Circuit Short to Battery
|
DTC
|
P274914
|
Intermediate Shaft Speed Sensor "C" Circuit Short to Ground or Open
|
DTC
|
P274931
|
Intermediate Shaft Speed Sensor "C" No Signal
|
DESCRIPTION
The transmission revolution sensor (NSS) detects the secondary pulley speed and sends it to the TCM.
The TCM determines the current gear ratio from the transmission revolution sensor (NSS) signal.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P274912
|
Intermediate Shaft Speed Sensor "C" Circuit Short to Battery
|
The transmission revolution sensor (NSS) signal is normal but the transmission revolution sensor (NSS) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic).
|
-
Wire harness or connector
-
Transmission revolution sensor (NSS)
-
TCM
|
Comes on
|
DTC stored
|
SAE Code:
P07CA
|
P274914
|
Intermediate Shaft Speed Sensor "C" Circuit Short to Ground or Open
|
The transmission revolution sensor (NSS) signal is normal but the transmission revolution sensor (NSS) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic).
|
-
Wire harness or connector
-
Transmission revolution sensor (NSS)
-
TCM
|
Comes on
|
DTC stored
|
SAE Code:
P07C9
|
P274931
|
Intermediate Shaft Speed Sensor "C" No Signal
|
When the transmission revolution sensor (NOUT) signal indicates 350 rpm or more and the transmission revolution sensor (NT) signal indicates 780 rpm or more, the transmission revolution sensor (NSS) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic).
|
-
Wire harness or connector
-
Transmission revolution sensor (NSS)
-
TCM
|
Comes on
|
DTC stored
|
SAE Code:
P2751
|
MONITOR DESCRIPTION
The TCM receives signals from the transmission revolution sensor (NSS) installed to the continuously variable transaxle and determines the secondary pulley speed in order to control the gear ratio.
If the TCM detects no signal from the transmission revolution sensor (NSS) even while the vehicle is being driven, it will determine that in the transmission revolution sensor (NSS) is malfunctioning, illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs
|
P07C9: Intermediate shaft speed sensor (for Belt Drive) (Transmission revolution sensor (NSS))/Range check (Low voltage)
P07CA: Intermediate shaft speed sensor (for Belt Drive) (Transmission revolution sensor (NSS))/Range check (High voltage)
P2751: Intermediate shaft speed sensor (for Belt Drive) (Transmission revolution sensor (NSS))/Verify pulse input
|
Required sensors/Components
|
Transmission revolution sensor (NSS)
Transmission revolution sensor (NT)
Transmission revolution sensor (NOUT)
|
Frequency of operation
|
Continuous
|
Duration
|
P07C9, P07CA: 4.5 sec.
P2751: 5 sec.
|
MIL operation
|
Immediate
|
Sequence of operation
|
None
|
TYPICAL ENABLING CONDITIONS
All
Battery voltage
|
8 V or more
|
Engine switch
|
On (IG)
|
Starter
|
OFF
|
P07C9, P07CA
Intermediate shaft speed sensor pulse input fail (P2751)
(Pending / MIL)
|
Not detected
|
P2751
Intermediate shaft speed sensor range check fail (P07C9, P07CA)
(Pending / MIL)
|
Not detected
|
D range position switch
|
ON
|
R range position switch
|
OFF
|
Park position switch
|
OFF
|
Neutral position switch
|
OFF
|
Engine
|
Running
|
Pressure control solenoid circuit fail (P08CA, P08CB, P0962, P0963, P0966, P0967, P2826, P2827, P282F, P2830)
(Pending + MIL)
|
Not detected
|
Torque converter clutch pressure control solenoid circuit fail (P2763, P2764)
(Pending + MIL)
|
Not detected
|
Output speed sensor revolution
|
350 rpm or more
|
Turbine speed sensor revolution
|
780 rpm or more
|
One of the following conditions is met: Condition (A) or (B)
-
Condition (A)
ECT
|
20°C (68°F) or more
|
ECT sensor circuit fail (P0117, P0118)
(Pending + MIL)
|
Not detected
|
All of the following conditions are met
|
2 sec. or more
|
- Park position switch
|
OFF
|
- Neutral position switch
|
OFF
|
Condition (B)
One of the following conditions is met
|
-
|
- ECT
|
Less than 20°C (68°F)
|
- ECT sensor circuit fail (P0117, P0118)
(Pending + MIL)
|
Detected
|
All of the following conditions are met
|
30 sec. or more
|
- Park position switch
|
OFF
|
- Neutral position switch
|
OFF
|
TYPICAL MALFUNCTION THRESHOLDS
P2751
Intermediate shaft speed sensor revolution
|
Less than 300 rpm
|
P07C9
Intermediate shaft speed sensor voltage
|
Less than 0.2 V
|
P07CA
Intermediate shaft speed sensor voltage
|
More than 1.8 V
|
COMPONENT OPERATING RANGE
P2751
Intermediate shaft speed sensor revolution
|
300 rpm or more
|
P07C9, P07CA
Intermediate shaft speed sensor voltage
|
0.2 V or more and 1.8 V or less
|
CONFIRMATION DRIVING PATTERN
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
-
Connect the Techstream to the DLC3.
-
Turn the engine switch on (IG) and turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the engine switch off and wait for 2 minutes or more.
-
Turn the engine switch on (IG) and turn the Techstream on.
-
Start the engine.
-
Perform the D Position Shift Test inspection in Road Test. [*1]
Click here
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
-
Stop the vehicle.
-
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
-
Input the DTC: P274912, P274914 or P274931.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
N/A
|
-
Unable to perform DTC judgment
-
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
|
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
-
Strictly observe posted speed, limits, traffic laws and road conditions.
-
Do not drive the vehicle with the cable of the Techstream contacting the pedals, shift lever or steering wheel.
-
Driving the vehicle with the cable of the Techstream contacting these areas could impede vehicle control, resulting in a serious accident.
-
Do not operate the Techstream while driving the vehicle.
-
Operating the Techstream while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM (NSS SENSOR SPEED AND NSS SENSOR VOLTAGE)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Transmission / Data List.
(e) According to the display on the Techstream, read the Data List.
Powertrain > Transmission > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
NSS Sensor Speed
|
Secondary pulley speed (NSS)
|
Min.: 0 rpm
Max.: 65535 rpm
|
-
0 rpm: Vehicle stopped and shift lever in D
-
Equal to NO Sensor Speed: Vehicle being driven in belt mode
|
-
|
NSS Sensor Voltage
|
Transmission revolution sensor (NSS) output voltage
|
Min.: 0.000 V
Max.: 4.999 V
|
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N)
|
-
|
Powertrain > Transmission > Data List
Tester Display
|
NSS Sensor Speed
|
NSS Sensor Voltage
|
Result
|
Proceed to
|
Data List values are normal
|
A
|
Data List values are not normal
|
B
|
A
|
|
|
(a) Replace the TCM.
Click here
3.
|
INSPECT TRANSMISSION REVOLUTION SENSOR (NSS)
|
(a) Remove the transmission revolution sensor (NSS).
Click here
(b) Connect the battery to the transmission revolution sensor (NSS) as shown in the illustration.
*1
|
Battery
|
*2
|
Ammeter
|
*a
|
Component without harness connected
(Transmission Revolution Sensor (NSS))
|
*b
|
Magnet
|
*c
|
5 mm or less
|
-
|
-
|
(c) Wave a magnet left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NSS) to output a high/low signal while measuring the current.
NOTICE:
Make sure to wave the magnet during the inspection. The current will not change unless the magnet is moved as shown in the illustration.
(d) Measure the current according to the value(s) in the table below.
Standard Current:
Tester Connection
|
Condition
|
Specified Condition
|
1 (NSSO) - 2 (NSSB)
|
Low signal
|
4 to 8 mA
|
1 (NSSO) - 2 (NSSB)
|
High signal
|
12 to 16 mA
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NSS) - TCM)
|
(a) Disconnect the C70 transmission revolution sensor (NSS) connector.
(b) Disconnect the C80 TCM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C70-1 (NSSO) - C80-7 (NSSO)
|
Always
|
Below 1 Ω
|
C70-2 (NSSB) - C80-23 (NSSB)
|
Always
|
Below 1 Ω
|
C70-1 (NSSO) or C80-7 (NSSO) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C70-2 (NSSB) or C80-23 (NSSB) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
(d) Connect the C80 TCM connector.
(e) Connect the C70 transmission revolution sensor (NSS) connector.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NSS) - TCM)
|
OK
|
|
|
(a) Replace the TCM.
Click here
|