| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001HEVK |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [01/2019 - 03/2019] |
| Title: SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: INSTALLATION; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019] | ||
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY
|
(a) Engage the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts. |
|
(b) Fully tighten the bolt (A) and then the bolt (B) to install the front shoulder belt anchor adjuster assembly.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY
Click here
![2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - ]; SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: INSPECTION+](/t3Portal/stylegraphics/info.gif)
3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY
|
(a) Engage the 2 guides and temporarily install the front seat outer belt assembly with the 2 bolts. |
|
(b) Fully tighten the bolt (A) and then the bolt (B) to install the front seat outer belt assembly.
Torque:
Bolt (A) :
12.5 N·m {127 kgf·cm, 9 ft·lbf}
Bolt (B) :
42 N·m {428 kgf·cm, 31 ft·lbf}
|
(c) Connect the pretensioner connector and lock the locking button as shown in the illustration. NOTICE: Securely lock the locking button. |
|
(d) Connect the shoulder anchor of the front seat outer belt assembly with the nut.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
(e) Check that the ELR locks.
NOTICE:
This check should be performed with the front seat outer belt assembly installed to the vehicle.
(1) With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.
4. INSTALL CENTER PILLAR UPPER GARNISH
Click here
5. INSTALL CENTER PILLAR LOWER GARNISH
Click here
6. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
(a) Connect the floor anchor of the front seat outer belt assembly with the bolt.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
7. INSTALL LAP BELT OUTER ANCHOR COVER
(a) Engage the 3 claws to install the lap belt outer anchor cover.
8. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
Click here
9. INSTALL REAR DOOR SCUFF PLATE (for Gasoline Model)
Click here
10. INSTALL REAR DOOR SCUFF PLATE (for HV Model)
Click here
11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Click here
12. INSTALL FRONT DOOR SCUFF PLATE
Click here
13. INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
w/o Rear Seat Heater: Click here
14. INSTALL REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
w/o Rear Seat Heater: Click here
15. CONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY (for Gasoline Model)
w/o Rear Seat Heater: Click here
16. INSTALL REAR SEAT ASSEMBLY (for Gasoline Model)
w/ Rear Seat Heater: Click here
17. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
18. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model: Click here
for Gasoline Model: Click here
19. INSPECT SRS WARNING LIGHT
for HV Model: Click here
for Gasoline Model: Click here
|
|