Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HE71
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [01/2019 - 03/2019]
Title: EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link
*1: for Hatchback

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

  • Rear door glass sub-assembly
  • Rear door glass run
  • Rear door belt moulding
  • Rear door inner glass weatherstrip

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (for Gasoline Model): INITIALIZATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link

Disconnect cable from negative (-) auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Control System

2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for HV Model): INITIALIZATION

Pre-collision System
  • Rear door glass sub-assembly
  • Rear door glass run
  • Rear door belt moulding
  • Rear door inner glass weatherstrip

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (for HV Model): INITIALIZATION

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for M20A-FKS:

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL+

for 2ZR-FAE:

Click here 2020 MY Corolla [01/2019 - 03/2019]; MAINTENANCE: 2ZR-FAE BATTERY: REMOVAL+

for 2ZR-FXE:

Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; MAINTENANCE: 2ZR-FXE AUXILIARY BATTERY: REMOVAL+

3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

6. REMOVE REAR SPEAKER ASSEMBLY

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL+

7. REMOVE REAR DOOR FRAME GARNISH

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

8. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

9. REMOVE REAR DOOR PANEL PROTECTOR

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

10. REMOVE REAR DOOR SERVICE HOLE COVER

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

11. REMOVE REAR DOOR GLASS RUN

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

12. DISCONNECT REAR DOOR WEATHERSTRIP

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR LOCK: REAR DOOR LOCK: REMOVAL+

13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

15. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP WITH REAR DOOR QUARTER WINDOW GLASS

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

16. REMOVE REAR DOOR BELT MOULDING (for Hatchback)

(a) Apply protective tape around the rear door belt moulding as shown in the illustration.

Protective Tape

(b) Disengage the 7 claws as shown in the illustration to remove the rear door belt moulding.

Remove in this Direction

17. REMOVE REAR DOOR BELT MOULDING (for Sedan)

(a) Apply protective tape around the rear door belt moulding as shown in the illustration.

Protective Tape

(b) Disengage the 8 claws as shown in the illustration to remove the rear door belt moulding.

Remove in this Direction