Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001HCLA |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [01/2019 - 03/2019] |
Title: SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): INSTALLATION; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019] |
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT SEAT ASSEMBLY
(a) Place the front seat assembly in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
|
|
(b) for Front Passenger Side:
(1) Connect the front seat cushion airbag assembly RH connector.
NOTICE:
-
When connecting any airbag connector, take care not to damage the airbag wire harness.
-
When connecting the connector, make sure to push it straight in.
(c) Connect the front seat airbag assembly connector under the front seat assembly.
(1) Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.
*a
|
Correct
|
*b
|
Incorrect
|
*c
|
Yellow CPA
|
*d
|
White Housing Lock
|
(2) Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).
NOTICE:
-
When connecting any airbag connector, take care not to damage the airbag wire harness.
-
When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.
(d) Connect each connector and engage each clamp under the front seat assembly.
(e) Temporarily install the front seat assembly with the 4 bolts.
(f) Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.
(g) Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.
Torque:
37 N·m {377 kgf·cm, 27 ft·lbf}
NOTICE:
Tighten the bolts in the order shown in the illustration.
|
|
(h) Operate the seat track adjusting handle and move the front seat assembly to the foremost position.
(i) Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.
Torque:
37 N·m {377 kgf·cm, 27 ft·lbf}
NOTICE:
Tighten the bolts in the order shown in the illustration.
|
|
2. INSPECT SEAT SLIDE ADJUSTER LOCK
(a) While performing a sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.
3. INSTALL INNER SEAT TRACK BRACKET COVER
(a) Operate the seat track adjusting handle and move the front seat assembly to the foremost position.
(b) Engage the 2 claws and guide to install the inner seat track bracket cover.
|
|
4. INSTALL OUTER SEAT TRACK COVER
(a) Engage the 2 claws and guide to install the outer seat track cover.
|
|
5. INSTALL FRONT INNER SEAT TRACK BRACKET COVER
(a) Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.
(b) Engage the 2 claws to install the front inner seat track bracket cover.
|
|
6. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER
(a) Engage the 2 claws to install the front outer seat track bracket cover.
|
|
7. INSTALL FRONT SEAT HEADREST ASSEMBLY
(a) Install the front seat headrest assembly to the front seat assembly.
8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
9. CHECK SEAT HEATER (w/ Seat Heater System)
Click here
10. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here
for HV Model: Click here
11. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Side)
for Gasoline Model: Click here
for HV Model: Click here
12. INSPECT FRONT SEAT ASSEMBLY (w/ Lumbar Support)
Click here
13. INSPECT SRS WARNING LIGHT
for Gasoline Model: Click here
for HV Model: Click here
|