LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model with AFS): PRECAUTION; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [01/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001HCKZ
Model Year Start: 2020	Model: GR Corolla	Prod Date Range: [01/2019 - 09/2022]
Title: LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model with AFS): PRECAUTION; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2022]

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected.

System Name	See Procedure
Lane Control System
Power Door Lock Control System (for Hatchback)
Pre-collision System
Lighting System (w/ AFS)(EXT)

PRECAUTION FOR BULB REPLACEMENT

(a) Always prepare a new bulb for immediate replacement. While replacing the bulb, the lens may attract dust and moisture if the bulb is removed from the vehicle for a long time.

(b) Always replace a bulb with another bulb of the same wattage.

(c) If only replacing the bulb on one side, differences in brightness and lighting color between the right and left sides may occur.

(d) Securely install the socket after bulb replacement. The lens may become cloudy or the light assembly may fill with water through gaps around the socket if it is not installed securely.

REPLACEMENT PRECAUTIONS

(a) When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PRECAUTIONS FOR AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM

(a) If any of the following are performed, it is necessary to initialize the headlight ECU sub-assembly LH.

Click here

Replacement of the rear height control sensor sub-assembly LH
Removal/installation of the rear height control sensor sub-assembly LH
Work that changes the vehicle height such as replacement of suspension components

(b) If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click here

PRECAUTION FOR AUTOMATIC HIGH BEAM SYSTEM

(a) General Description

The automatic high beam system is a system that helps ensure visibility by automatically turning the high beam headlights on and off. Additionally, due to control limitations of the automatic high beam system, it may be necessary to manually turn the high beam headlights on and off. For safety reasons, make sure to turn the high beam headlights on and off manually according to the driving conditions.

(b) Conditions Unsuitable for Using Automatic High Beam System

Under the following conditions, the automatic high beam system might not detect other vehicles or lights correctly, or the high beam headlights might cause glare or flash pedestrians or the occupants of other vehicles. Manual operation should be considered.

Factor	Condition
Weather/Climate	When driving in bad weather (rain, snow, fog, sandstorms, etc.).
Front windshield	When the windshield glass is dirty (mud, water stains, insects, etc.) or there is dirt or fogging on the vehicle interior side.* When the windshield glass is cracked or damaged. Windshield glass with an incorrect transmissivity is installed (non-genuine part).
Forward recognition camera	Refer to Front Camera System.
Nearby vehicles or lights	When lights similar to headlights or taillights are in the vicinity of the vehicle. When a nearby vehicle has no lights or its lights are off. When a vehicle in front has misaligned lights, or its lights are changing color. When a vehicle in front has extremely dirty headlights or taillights.
Road conditions	When driving in areas where the conditions often change between bright and dark. When driving on hilly roads. When driving on winding roads or around sharp curves. When driving on bumpy roads (cobblestone paving, gravel roads, rough unpaved roads, etc.). When highly reflective objects are in front of the vehicle (mirrors, road signs, etc.).
Own vehicle	When the headlights are damaged, deformed or dirty. When the vehicle posture is abnormal (posture has changed due to the vehicle being fully loaded, a trailer being towed, road conditions, etc.). When the vehicle has other malfunctions or has been modified.
Automatic high beam system	Malfunction: When the automatic high beam indicator light on the combination meter assembly is off and "Headlight System Malfunction Visit Your Dealer" is displayed on the multi-information display. Others: When the automatic high beam system does not seem to be turning the high beam headlights on and off properly. When the automatic high beam system is frequently turning the high beam headlights on and off. When the glare from the high beam headlights would disturb pedestrians or the drivers of other vehicles.

HINT:

*: If it is confirmed that the inside of the windshield glass is dirty, remove the forward recognition camera and hood and perform any of the following cleaning methods to clean the windshield glass.

Remove the dirt using a sponge and water, and then wipe clean using a towel, cloth or similar item.
Clean using glass cleaner.

(Even though the forward recognition camera is removed and installed when cleaning, it is not necessary to perform an axis alignment.)

To remove the forward recognition camera, refer to

PRECAUTION FOR FRONT CAMERA SYSTEM

Click here