| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001HCCC |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [01/2019 - 03/2019] |
| Title: METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative (-) auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for HV Model) |
|
|
Pre-collision System (for HV Model) |
NOTICE:
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System)
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
| *1: for Hatchback | |||
|
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for Gasoline Model) |
|
|
Pre-collision System (for Gasoline Model) |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock*1 |
Power Door Lock Control System (for Hatchback, Gasoline Model) |
|
|
NOTICE:
- After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. REMOVE NO. 1 INSTRUMENT SIDE PANEL
Click here
![2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL+](/t3Portal/stylegraphics/info.gif)
3. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
4. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Click here
5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL
Click here
6. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Click here
7. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
8. REMOVE AIR CONDITIONING CONTROL ASSEMBLY
Click here
9. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
Click here
10. REMOVE NO. 2 INSTRUMENT SIDE PANEL
Click here
11. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Click here
12. REMOVE UPPER STEERING COLUMN COVER
Click here
13. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Click here
14. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here
15. REMOVE INSTRUMENT CLUSTER FINISH PANEL RETAINER
Click here
16. REMOVE COMBINATION METER ASSEMBLY
|
(a) Remove the 4 screws. |
|
|
(b) Disengage the clamp. |
|
(c) Disconnect the 2 connectors to remove the combination meter assembly.
|
|