Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HCBA
Model Year Start: 2020 Model: Corolla Hatchback Prod Date Range: [01/2019 - 03/2019]
Title: EG60 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE (for TMC Made): ADJUSTMENT; 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]

ADJUSTMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly adjustment are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*1: for Hatchback

*2: w/ Smart Key System

*3: w/o Smart Key System

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System (for Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System (for Gasoline Model)

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System (for Hatchback, Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

Replacement of ECM*2

Code registration (Smart Key System (for Gasoline Model, Start Function))
  • Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
  • Smart Key System (for Gasoline Model, Entry Function)
  • Smart Key System (for Gasoline Model, Start Function)
  • Steering lock function

2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

Replacement of ECM*3

Code registration (Immobiliser system)

Engine start

2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

  • Make sure to apply the parking brake and chock a wheel before performing this procedure.
  • If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL+

4. REMOVE BATTERY

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL

5. REMOVE CONSOLE BOX ASSEMBLY

Click here 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 09/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (except G16E-GTS): REMOVAL

6. REMOVE RADIATOR SUPPORT OPENING COVER (for Hatchback)

Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Hatchback except GR): REMOVAL+

7. REMOVE RADIATOR SUPPORT OPENING COVER (w/ Illumination)

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Sedan with Illumination): REMOVAL+

8. REMOVE INLET NO. 1 AIR CLEANER

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (COOLING): COOLING FAN MOTOR (w/o Cooling Fan ECU): REMOVAL+

9. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (ENGINE CONTROL): THROTTLE BODY: REMOVAL+

10. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; MAINTENANCE: M20A-FKS AIR CLEANER FILTER ELEMENT: REMOVAL+

11. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (ENGINE CONTROL): ECM: REMOVAL+

12. REMOVE ECM

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (ENGINE CONTROL): ECM: REMOVAL+

13. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

14. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:

  • After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.
  • If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.

(a) Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.

(b) Slide the slider of the transmission control select cable in the direction indicated by the arrow in the illustration and pull the lock piece outward.

*a

Slider

*b

Lock Piece

*c

Slide

*d

Pull

(c) Connect the transmission control select cable to the floor shift shift lever assembly and install the clip.

NOTICE:

  • Check that the lock piece is pulled out.
  • Push the end of the transmission control select cable all the way to the base of the floor shift shift lever assembly pin.
  • Connect the transmission control select cable so that the lock piece faces the driver side.

*a

Lock Piece

(d) Align the hole of the outer select lever with the hole in the manual transmission case.

*1

Outer Select Lever

*a

Hole of Manual Transmission Case

*b

Hole of Outer Select Lever

(e) Insert a bolt into the aligned holes to secure the outer select lever in place.

NOTICE:

Do not push in the bolt forcefully or damage the front transaxle case.

HINT:

  • Use a bolt with a diameter of 6 mm (0.236 in.) and a length of at least 36 mm (1.42 in.).
  • Depending on the bolt diameter, it may be difficult to insert the bolt. In that case, use a bolt with a diameter smaller than 6 mm (0.236 in.).

(f) Push the slider shaft against the cam wall.

NOTICE:

  • Do not pull up the slider shaft.
  • When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

*a

Slider Shaft

*b

Cam Wall

(g) Push the lock piece into the adjuster case.

*a

Lock Piece

*b

Adjuster Case

*c

Push

-

-

NOTICE:

Securely push in the lock piece until the slider lock is engaged.

(h) Remove the bolt to release the select outer lever.

15. INSTALL BATTERY CLAMP SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+

16. INSTALL ECM

Click here 2020 - 2022 MY Corolla Corolla Hatchback [01/2019 - 09/2022]; M20A-FKS (ENGINE CONTROL): ECM: INSTALLATION+

17. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click here 2020 - 2022 MY Corolla Corolla Hatchback [01/2019 - 09/2022]; M20A-FKS (ENGINE CONTROL): ECM: INSTALLATION+

18. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; MAINTENANCE: M20A-FKS AIR CLEANER FILTER ELEMENT: INSTALLATION+

19. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (ENGINE CONTROL): THROTTLE BODY: INSTALLATION+

20. INSTALL INLET NO. 1 AIR CLEANER

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (COOLING): COOLING FAN MOTOR (w/o Cooling Fan ECU): INSTALLATION+

21. INSTALL RADIATOR SUPPORT OPENING COVER (for Hatchback)

Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Hatchback except GR): INSTALLATION+

22. INSTALL RADIATOR SUPPORT OPENING COVER (w/ Illumination)

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Sedan with Illumination): INSTALLATION+

23. INSTALL CONSOLE BOX ASSEMBLY

Click here 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 09/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (except G16E-GTS): INSTALLATION

24. INSTALL BATTERY

Click here 2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; MAINTENANCE: M20A-FKS BATTERY: INSTALLATION

25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here 2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; MAINTENANCE: M20A-FKS BATTERY: INSTALLATION+