Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HCB7
Model Year Start: 2020 Model: Corolla Hatchback Prod Date Range: [01/2019 - 03/2019]
Title: M20A-FKS (BATTERY / CHARGING): GENERATOR (for Transaxle CVT with Denso Made Generator): REMOVAL; 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during generator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*1: for Hatchback

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Control System (for Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System (for Gasoline Model)

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System (for Hatchback, Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL+

2. REMOVE RADIATOR SUPPORT OPENING COVER

  • for Hatchback

    Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Hatchback except GR): REMOVAL+

  • w/ Illumination

    Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Sedan with Illumination): REMOVAL+

3. REMOVE INLET NO. 1 AIR CLEANER

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (COOLING): COOLING FAN MOTOR (w/o Cooling Fan ECU): REMOVAL+

4. REMOVE V-RIBBED BELT

Click here 2020 - 2025 MY Corolla Corolla Hatchback [01/2019 -        ]; MAINTENANCE: M20A-FKS DRIVE BELT: REMOVAL

5. REMOVE GENERATOR ASSEMBLY

(a) Disconnect the generator assembly connector.

(b) Open the terminal cap.

(c) Remove the nut and disconnect the wire harness from terminal B.

(d) Remove the bolt and separate the wire harness clamp bracket from the generator assembly.

(e) Remove the 2 nuts bolt and generator assembly.