Last Modified: 01-27-2025 6.11:8.1.0 Doc ID: RM100000001HCB5
Model Year Start: 2020 Model: Corolla Hatchback Prod Date Range: [01/2019 - 03/2019]
Title: M20A-FKS (STARTING): STARTER: REMOVAL; 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during starter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*1: for Hatchback

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Control System (for Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System (for Gasoline Model)

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System (for Hatchback, Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

  • Cleaning the deposits from the throttle body with motor assembly
  • Gas leak from exhaust system is repaired

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc.

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; MAINTENANCE: M20A-FKS BATTERY: REMOVAL+

3. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE INTAKE MANIFOLD

Click here 2020 - 2022 MY Corolla Corolla Hatchback [01/2019 - 09/2022]; M20A-FKS (INTAKE / EXHAUST): INTAKE MANIFOLD: REMOVAL

5. REMOVE FLYWHEEL HOUSING SIDE COVER

(a) Disengage the claw as shown in the illustration to remove the flywheel housing side cover.

6. REMOVE STARTER ASSEMBLY

(a) Disconnect the starter assembly connector.

(b) Disengage the claw and remove the starter assembly cover (cover B) from the starter assembly cover (base) and starter assembly cover (cover A).

(c) Remove the nut to disconnect the engine wire from terminal 30.

(d) Remove the bolt and disconnect the engine wire.

*A

for Manual Transaxle

*B

for CVT

(e) Remove the 2 bolts and starter assembly.

(f) Remove the starter assembly cover (cover A) from the starter assembly cover (base).

(g) Remove the nut and starter terminal from the starter assembly.

(h) Disengage the 2 claws and remove the starter terminal from the starter assembly cover (base).