| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001HC9D |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [01/2019 - 03/2019] |
| Title: SEAT BELT: FRONT SEAT INNER BELT ASSEMBLY: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for HV Model) |
|
|
Pre-collision System (for HV Model) |
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: for Hatchback | |||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for Gasoline Model) |
|
|
Pre-collision System (for Gasoline Model) |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock*1 |
Power Door Lock Control System (for Hatchback, Gasoline Model) |
|
|
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
for HV Model: Click here
![2020 MY Corolla Corolla HV [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for Gasoline model: Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
- After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
- After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
Click here
2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
Click here
3. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
(a) for Manual Seat:
(1) Disconnect the connector.
|
(2) Disengage each clamp. |
|
(3) Remove the nut and front seat inner belt assembly.
(4) Remove the front seat belt anchor plate as shown in the illustration.
|
Remove in this Direction |
(b) for Power Seat:
(1) Disconnect the 2 connectors.
|
(2) Disengage each clamp. |
|
(3) Remove the nut and front seat inner belt assembly.
(4) Remove the front seat belt anchor plate as shown in the illustration.
|
|
Remove in this Direction |
4. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
(a) Disconnect the connector.
|
(b) Disengage each clamp. |
|
(c) Remove the nut and front seat inner belt assembly.
(d) Remove the front seat belt anchor plate as shown in the illustration.
|
|
Remove in this Direction |
|
|