Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001HC9D
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [01/2019 - 03/2019]
Title: SEAT BELT: FRONT SEAT INNER BELT ASSEMBLY: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Control System (for HV Model)

2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for HV Model): INITIALIZATION

Pre-collision System (for HV Model)

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*1: for Hatchback

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System (for Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System (for Gasoline Model)

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System (for Hatchback, Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    for HV Model: Click here 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION

    for Gasoline model: Click here 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:

  • After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REMOVAL

2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; SEAT: FRONT SEAT ASSEMBLY (for Power Seat): REMOVAL

3. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

(a) for Manual Seat:

(1) Disconnect the connector.

(2) Disengage each clamp.

(3) Remove the nut and front seat inner belt assembly.

(4) Remove the front seat belt anchor plate as shown in the illustration.

Remove in this Direction

(b) for Power Seat:

(1) Disconnect the 2 connectors.

(2) Disengage each clamp.

(3) Remove the nut and front seat inner belt assembly.

(4) Remove the front seat belt anchor plate as shown in the illustration.

Remove in this Direction

4. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

(a) Disconnect the connector.

(b) Disengage each clamp.

(c) Remove the nut and front seat inner belt assembly.

(d) Remove the front seat belt anchor plate as shown in the illustration.

Remove in this Direction