| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001H97H |
| Model Year Start: 2020 | Model: Corolla | Prod Date Range: [01/2019 - 09/2022] |
| Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM (for HV Model): B1475; A/C Inverter Cooling / Heating System; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] | ||
|
DTC |
B1475 |
A/C Inverter Cooling / Heating System |
DESCRIPTION
The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.
If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
|---|---|---|---|---|
|
B1475 |
A/C Inverter Cooling / Heating System |
A/C inverter temperature outside specified range (temperature too high) or open or short to ground in temperature sensor circuit |
|
Memorized |
CAUTION / NOTICE / HINT
CAUTION:
- Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
- Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
NOTICE:
-
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.
-
The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.
Click here
PROCEDURE
|
1. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Powertrain > Engine > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Control the Engine Cooling Fan |
Control electric cooling fan motor |
OFF, Low or High |
Perform this test when vehicle is stopped. |
Powertrain > Engine > Active Test
|
Tester Display |
|---|
|
Control the Engine Cooling Fan |
OK:
Cooling fan operates smoothly.
| NG |
|
|
|
2. |
CHECK REFRIGERANT PRESSURE |
(a) Install a manifold gauge set.
for HFC-134a (R134a): Click here
for HFO-1234yf (R1234yf): Click here
(b) Turn the power switch on (READY).
(c) Read the manifold gauge pressure when the following conditions are met.
(1) Prepare the vehicle according to the table below.
|
Item |
Condition |
|---|---|
|
Vehicle doors |
Fully open |
|
Temperature setting |
MAX COLD |
|
Blower speed |
HI |
|
A/C switch |
On |
|
Recirculation/fresh switch |
RECIRCULATION |
|
Interior temperature |
25 to 35°C (77 to 95°F) |
Standard Pressure:
Low pressure side
150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
High pressure side
1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)
| NG |
|
CHARGE REFRIGERANT for HFC-134a (R134a): Click here
for HFO-1234yf (R1234yf): Click here
|
|
|
3. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
(e) Clear the DTCs.
Body Electrical > Air Conditioner > Clear DTCs
|
|
4. |
READ OUTPUT DTC (DTC B1475) |
(a) Prepare the vehicle according to the table below.
|
Item |
Condition |
|---|---|
|
Blower speed |
HI |
|
A/C switch |
On |
|
Temperature setting |
MAX COLD |
(b) Turn the power switch on (READY).
(c) Connect the Techstream to the DLC3.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
(f) Check for DTCs.
Body Electrical > Air Conditioner > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
B1475 is not output |
A |
|
B1475 is output |
B |
NOTICE:
If the engine idles continuously when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475 may be stored.
| A |
|
| B |
|
REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
|
|
|