Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001H8SZ |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): Immobiliser System does not Operate Properly; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2022] |
Immobiliser System does not Operate Properly
|
DESCRIPTION
The immobiliser function compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
HINT:
If an immobiliser function or SFI system DTC is output, first perform troubleshooting for the immobiliser function or SFI system DTC.
PROCEDURE
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble Codes
Powertrain > Engine > Trouble Codes
Powertrain > Engine and ECT > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTCs are output
|
B
|
A
|
|
|
2.
|
READ VALUE USING TECHSTREAM (IMMOBILISER FUEL CUT STATUS, IMMOBILISER FUEL CUT)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine*1 or Engine and ECT*2 / Data List.
-
*1: for M20A-FKS
-
*2: for 2ZR-FAE
(e) Read the Data List according to the display on the Techstream.
Powertrain > Engine > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Immobiliser Fuel Cut Status
|
Status of immobiliser fuel cut
|
OFF or ON
|
-
|
-
|
Powertrain > Engine > Data List
Tester Display
|
Immobiliser Fuel Cut Status
|
Powertrain > Engine and ECT > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Immobiliser Fuel Cut
|
Status of immobiliser fuel cut
|
OFF or ON
|
-
|
-
|
Powertrain > Engine and ECT > Data List
Tester Display
|
Immobiliser Fuel Cut
|
OK:
OFF is displayed after the engine is started.
OK |
|
GO TO SFI SYSTEM
for M20A-FKS: Click here
for 2ZR-FAE: Click here
|
NG
|
|
|
3.
|
CHECK WHETHER ENGINE STARTS
|
(a) Check that the engine starts 5 seconds after the engine switch turned on (IG).
OK:
Engine starts normally.
NG
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
|
(a) Disconnect the I20 ID code box (immobiliser code ECU) connector.
(b) Disconnect the A47*1 or A46*2 ECM connector.
-
*1: for M20A-FKS
-
*2: for 2ZR-FAE
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for M20A-FKS
Tester Connection
|
Condition
|
Specified Condition
|
I20-3 (EFII) - A47-25 (IMO)
|
Always
|
Below 1 Ω
|
I20-4 (EFIO) - A47-26 (IMI)
|
Always
|
Below 1 Ω
|
I20-3 (EFII) or A47-25 (IMO) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
I20-4 (EFIO) or A47-26 (IMI) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
for 2ZR-FAE
Tester Connection
|
Condition
|
Specified Condition
|
I20-3 (EFII) - A46-45 (IMO)
|
Always
|
Below 1 Ω
|
I20-4 (EFIO) - A46-28 (IMI)
|
Always
|
Below 1 Ω
|
I20-3 (EFII) or A46-45 (IMO) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
I20-4 (EFIO) or A46-28 (IMI) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
CHECK ECM (TERMINAL EFIO AND EFII)
|
(a) Connect the I20 ID code box (immobiliser code ECU) connector.
(b) Connect the A47*1 or A46*2 ECM connector.
-
*1: for M20A-FKS
-
*2: for 2ZR-FAE
(c) Using an oscilloscope, check the waveform.
*a
|
Component with harness connected
(ID Code Box (Immobiliser Code ECU))
|
*b
|
Approximately 160 ms.
|
*c
|
Approximately 270 ms.
|
*d
|
Approximately 40 ms.
|
*e
|
Approximately 60 ms.
|
*f
|
Waveform (EFII)
|
*g
|
Waveform (EFIO)
|
*h
|
Waveform A
|
*i
|
Waveform B
|
*j
|
Waveform C
|
*k
|
Waveform A (detail)
|
-
|
-
|
NOTICE:
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
OK:
Tester Connection
|
Condition
|
Tool Setting
|
Specified Condition
|
I20-3 (EFII) - Body ground
|
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
|
2 V/DIV., 500 ms./DIV.
|
Pulse generation
(See waveform (EFII))
|
I20-4 (EFIO) - Body ground
|
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
|
2 V/DIV., 500 ms./DIV.
|
Pulse generation
(See waveform (EFIO))
|
Result
|
Proceed to
|
Normal waveform
|
A
|
Waveform A or C not output, or has abnormal wavelength or shape
|
B
|
Waveform B not output, or has abnormal wavelength or shape
|
C
|
A
|
|
|
6.
|
REGISTER ECU COMMUNICATION ID
|
(a) Register the ECU communication ID.
Click here
NEXT
|
|
|
7.
|
CHECK WHETHER ENGINE STARTS
|
(a) Check that the engine starts.
OK:
Engine starts normally.
OK |
|
END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)
|
|