Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001H8E2 |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): System Malfunction Message is Displayed on the Multi-information Display; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] |
System Malfunction Message is Displayed on the Multi-information Display
|
SYSTEM DESCRIPTION
If an abnormal operation that may lead to a malfunction of the steering lock ECU (steering lock actuator or upper bracket assembly), or abnormal vehicle speed information is detected by the certification ECU (smart key ECU assembly), a system malfunction message is displayed on the multi-information display.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus Body Electrical Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Click here
-
Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Registration.
Click here
PROCEDURE
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble Codes
Body Electrical > Power Source Control > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTC U0129 is output.
|
B
|
DTC B2271, B2278, B2282, B2781, B2782, B2788 or U0155 is output.
|
C
|
A
|
|
|
2.
|
READ VALUE USING TECHSTREAM (STEERING LOCK)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Sensor Value
|
History of malfunction of position sensor in steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B2781 is stored)
|
OK or NG(Past)
|
OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) does not exist.
NG(Past): History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator or upper bracket assembly) being on exists. (Under normal operation, neither sensor is on.)
|
When NG(Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) or the assembly itself may be malfunctioning.
|
Body Electrical > Smart Key > Data List
Tester Display
|
Sensor Value
|
OK:
OK is displayed on the Techstream.
OK
|
|
|
3.
|
READ VALUE USING TECHSTREAM (SENSOR BALUE)
|
(a) Enter the following menus: Body Electrical / Power Source Control / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
IG Circuit
|
IG relay coil circuit malfunction
|
OK or NG
|
OK: Circuit normal
NG: Circuit malfunctioning
|
-
Use this item to determine if the IG relay is malfunctioning.
-
When the engine hybrid control system be started due to an IG relay malfunction, NG is displayed.
|
Body Electrical > Power Source Control > Data List
Tester Display
|
IG Circuit
|
Result
|
Proceed to
|
"NG" is displayed on the Techstream
|
A
|
"OK" is displayed on the Techstream
|
B
|
A
|
|
|
4.
|
READ VALUE USING TECHSTREAM (VEHICLE SPEED SIGNAL)
|
(a) Enter the following menus: Body Electrical / Power Source Control / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Vehicle Speed Signal
|
Vehicle being driven or stopped
|
Stop or Run
|
Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
|
-
|
Body Electrical > Power Source Control > Data List
Tester Display
|
Vehicle Speed Signal
|
OK:
The Techstream display changes correctly in response to the vehicle condition.
OK
|
|
|
5.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE)
|
(a) Disconnect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I59-1 (GND) - Body ground
|
Always
|
Below 1 Ω
|
NOTICE:
If the result is not as specified, check for looseness in the ground cable connection.
|
|
*a
|
Front view of wire harness connector
(to Steering Lock ECU Steering Lock Actuator or Upper Bracket Assembly))
|
|
|
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I59-7 (B) - Body ground
|
Power switch off
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
6.
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
|
(a) Connect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I59-3 (IGE) - I59-1 (GND)
|
-
Steering lock motor operating when all conditions met, and then door opened:
-
The steering is unlocked.
-
The power switch is off.
-
The shift lever is in P.
|
11 to 14 V → Below 1 V
|
|
|
*a
|
Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
|
|
|
NG
|
|
|
7.
|
CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
|
(a) Disconnect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Disconnect the I1 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I59-3 (IGE) - I1-25 (SLR+)
|
Always
|
Below 1 Ω
|
I59-3 (IGE) or I1-25 (SLR+) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
8.
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
|
(a) Connect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I59-3 (IGE) - Body ground
|
Power switch off
|
11 to 14 V
|
|
|
*a
|
Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
|
|
|
|