| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001H8E1 |
| Model Year Start: 2020 | Model: Corolla | Prod Date Range: [01/2019 - 09/2022] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): New Key Registration Warning Message is not Displayed; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] | ||
|
New Key Registration Warning Message is not Displayed |
DESCRIPTION
If the new key registration warning message is not displayed after an electrical key transmitter sub-assembly has been registered, there may be communication problem between the certification ECU (smart key ECU assembly) and combination meter assembly (meter ECU).
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus Body Electrical Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Click here
![2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here
- After repair, confirm that no DTCs are output.
- Check that there are no electrical key transmitter sub-assemblies in the vehicle.
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTCs are output |
B |
| B |
|
GO TO DIAGNOSTIC TROUBLE CODE CHART
|
|
|
2. |
READ VALUE USING TECHSTREAM (FL DOOR COURTESY SW) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
FL Door Courtesy SW |
Front door LH courtesy light switch signal |
OFF or ON |
OFF: Front door LH closed ON: Front door LH open |
- |
Body Electrical > Main Body > Data List
|
Tester Display |
|---|
|
FL Door Courtesy SW |
|
Result |
Proceed to |
|---|---|
|
On the Techstream screen, ON or OFF is displayed accordingly. |
A |
|
On the Techstream screen, ON or OFF is not displayed accordingly. |
B |
| B |
|
|
|
3. |
CHECK METER / GAUGE SYSTEM |
(a) With the electrical key transmitter sub-assembly in the vehicle and all of the doors closed, lock the doors using the entry lock function and check that the warning message is displayed on the multi-information display.
NOTICE:
In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.
HINT:
Key lock-in prevention function (vehicle interior).
Click here
|
Result |
Proceed to |
|---|---|
|
The warning message is displayed on the multi-information display. |
A |
|
The warning message is not displayed on the multi-information display. |
B |
| B |
|
|
|
4. |
ADDITIONAL KEY REGISTRATION |
(a) Clear all of the registered electrical key transmitter sub-assemblies except one and perform registration again.
Click here
|
|
5. |
CHECK MULTI-INFORMATION DISPLAY |
(a) With all of the doors closed, lock the doors using the entry lock function.
(b) Unlock the doors using the entry unlock function, open the driver door and check that the warning message is displayed on the multi-information display.
|
Result |
Proceed to |
|---|---|
|
The warning message is displayed on the multi-information display. |
A |
|
The warning message is not displayed on the multi-information display. |
B |
| A |
|
END (10 DAYS MAY HAVE ELAPSED SINCE AN ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS REGISTERED) |
| B |
|
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
|
|
|