Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001H8DB
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 09/2022]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): B2277; Detecting Vehicle Submersion; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]

DTC

B2277

Detecting Vehicle Submersion

DESCRIPTION

This DTC is stored when a malfunction in the water submersion detection circuit inside the certification ECU (smart key ECU assembly) is detected.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B2277

Detecting Vehicle Submersion

Water submersion detected by the water submersion detection circuit inside the certification ECU (smart key ECU assembly). (1-trip detection logic*)

Certification ECU (smart key ECU assembly)

DTC Output Confirmation Operation:

  • Wait 300 seconds after connecting the cable to the negative (-) auxiliary battery terminal.
  • *: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Function when Malfunction Detected

The power switch cannot be turned off and the hybrid control system cannot be started.

-

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2277

-

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus Body Electrical Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

HINT:

Before proceeding with troubleshooting, check if there are any signs of water damage to the certification ECU (smart key ECU assembly). If there are any signs of water damage, replace the certification ECU (smart key ECU assembly) and take measures against the cause of the water damage.

PROCEDURE

1.

CHECK WATER INTRUSION

(a) Check that the certification ECU (smart key ECU assembly), its ground area and wire harnesses have no signs of water intrusion.

Result

Proceed to

No sign of water intrusion found

A

Signs of water intrusion found

B
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

B

TAKE MEASURES AGAINST WATER INTRUSION AND REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)