Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GYSE
Model Year Start: 2020 Model: Corolla Hatchback Prod Date Range: [01/2019 - 11/2022]
Title: K313 (CVT): CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: DATA LIST / ACTIVE TEST; 2020 - 2023 MY Corolla Corolla Hatchback [01/2019 - 11/2022]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:

  • To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
  • When selecting a measurement group, the ECM data belonging to that group is displayed.

(g) According to the display on the Techstream, read the Data List.

Powertrain > Engine and ECT > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed

Vehicle speed

Min.: 0 km/h (0 mph)

Max.: 255 km/h (158 mph)

Actual vehicle speed
  • This is the current vehicle speed.
  • The vehicle speed is detected using the wheel speed sensors.
  • Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

Engine Speed

Engine speed

Min.: 0 rpm

Max.: 16383.75 rpm

700 to 800 rpm: Engine idling

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

MAF

Airflow rate from mass air flow meter sub-assembly

Min.: 0 gm/sec.

Max.: 655.35 gm/sec.
  • 1.0 to 3.0 gm/sec: Engine idling
  • 3.0 to 8.0 gm/sec: 3000 rpm (without load)

This is the intake air amount detected by the mass air flow meter sub-assembly.

MAP

Intake manifold pressure

Min.: 0 kPa (0 psi), Max.: 255 kPa (36.98 psi)
  • 80 to 110 kPa(abs) [11.6 to 15.95 psi(abs)]: Ignition switch ON
  • 20 to 40 kPa(abs) [2.9 to 5.8 psi(abs)]: Engine idling (engine warmed up, A/C off and shift lever in P or neutral)
  • When the ignition switch is ON, the manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa(abs) [14.65 psi(abs)]).
  • MAP is almost the same as Atmospheric Pressure when the engine is stopped, these items can be used to help determine if the manifold absolute pressure sensor characteristics are abnormal, if there is noise, or if the sensor output is stuck at a certain value by comparing the values.

Coolant Temp

Coolant temperature

Min.: -40°C (-40°F)

Max.: 140°C (284°F)

75 to 100°C (167 to 212°F): After warming up
  • After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).
  • After a cold soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.
  • Check if the engine is overheating if the value indicates 140°C (284°F).

Throttle Motor DUTY

Throttle actuator

Min.: 0%

Max.: 100%

10 to 22%: Engine idling

This is the output duty ratio of the throttle actuator drive circuit.

Starter Signal

Starter signal

OFF or ON
  • ON: Starter operating
  • OFF: Starter not operating

-

Neutral Position SW Signal

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in P or N
  • ON: Shift lever in P or N

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

Stop Light Switch

Stop light switch status

OFF or ON
  • OFF: Brake pedal released
  • ON: Brake pedal depressed

-

A/C Signal

A/C switch status

OFF or ON

ON: A/C switch on

-

Closed Throttle Position SW

Closed throttle position switch

OFF or ON
  • ON: Throttle fully closed
  • OFF: Throttle open

-

SPD (NT)

Input turbine speed (NT)

Min.: 0 rpm

Max.: 65535 rpm
  • Equal to engine speed (NE): Lock-up ON (After warming up engine)
  • Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N)
  • 0 rpm: Vehicle stopped with shift lever in R

Data is displayed in increments of 50 rpm.

Shift SW Status (P Range)

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in P
  • ON: Shift lever in P

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

Pattern Switch (PWR/M)

SPORT mode status

OFF or ON
  • OFF: SPORT mode off
  • ON: SPORT mode on

-

Shift SW Status (R Range)

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in R
  • ON: Shift lever in R

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

Shift SW Status (N Range)

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in N
  • ON: Shift lever in N

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

Shift SW Status (N,P Range) Supported

Shift lever position P or N support status

Supp or Unsupp

Supp: Normal

-

Shift SW Status (N,P Range)

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in P or N
  • ON: Shift lever in P or N

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

Shift SW Status (D Range)

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in D
  • ON: Shift lever in D

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

A/T Oil Temperature 1

CVT fluid temperature sensor value

Min.: -40°C (-40°F)

Max.: 150°C (302°F)
  • Approximately 100°C (212°F): After stall speed test
  • Equal to ambient temperature: After cold soak

If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.

ATF Thermal Degradation Estimate

Estimated value of ATF thermal degradation

Min.: 0

Max.: 65535

-

If 50000 or more is displayed, thermal degradation of the CVT fluid is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the CVT fluid.

NT Sensor Voltage

Transmission revolution sensor (NT) output voltage

Min.: 0.000 V

Max.: 4.999 V

0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N)

-

Shift SW Status (B Range)

Park/neutral position switch status

OFF or ON
  • OFF: Shift lever not in B
  • ON: Shift lever in B

When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.

HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*.

SPD (NIN)

Primary pulley speed (NIN)

Min.: 0 rpm

Max.: 65535 rpm
  • 0 rpm: Vehicle stopped
  • Equal to engine speed (NE): Lock-up ON (After warming up engine)

Data is displayed in increments of 50 rpm.

SPD (NOUT)

Secondary pulley speed (NOUT)

Min.: 0 rpm

Max.: 65535 rpm
  • 0 rpm: Vehicle stopped
  • Approximately 3000 rpm: Vehicle being driven at approximately 60 km/h (37 mph)

Data is displayed in increments of 50 rpm.

NOUT Sensor Voltage

Transmission revolution sensor (NOUT) output voltage

Min.: 0.000 V

Max.: 4.999 V

0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N)

-

A/T Oil Pressure

Secondary oil pressure value

Min.: -64 MPa

Max.: 63.998 MPa

Secondary oil pressure inspection:

  • 3.6 to 4.8 MPa (36.7 to 48.9 kgf/cm2, 522 to 696 psi): D position stall test
  • 3.7 to 4.8 MPa (37.7 to 48.9 kgf/cm2, 537 to 696 psi): R position stall test

-

G Sensor

Converted output voltage of yaw rate and acceleration sensor

Min.: 0 V

Max.: 79.998 V
  • 2.31 to 2.69 V: Vehicle on level ground
  • 1.88 to 2.5 V: Decelerating
  • 2.5 to 3.11 V: Accelerating
  • Stuck at 1.87 V: G sensor malfunction
  • Stuck at 1.87 V: Communication malfunction

-

Lock Up

Lock-up

OFF or ON
  • ON: Lock-up operating
  • OFF: Lock-up not operating

-

CVT Shift Status Ratio

ECM gear ratio command

Min.: 0

Max.: 15.999

Same as actual gear ratio

-

Shift Range Indicator

ECM gearshift command

OFF, 1st, 2nd, 3rd, 4th, 5th, 6th, 7th, 8th, 9th or 10th

OFF

-

Solenoid (SLS)

Shift solenoid valve SLS status

OFF or ON
  • ON: After engine start
  • OFF: Ignition switch ON

-

SLU Solenoid Status

Shift solenoid valve SLU status

OFF or ON
  • ON: Lock-up permitted
  • OFF: Lock-up not permitted

-

SL Solenoid Status

Shift solenoid valve SL status

OFF or ON
  • ON: Lock-up permitted
  • OFF: Lock-up not permitted

-

Solenoid(SC)

Shift solenoid valve SC status

OFF or ON
  • ON: For 1 second after moving shift lever from P to D or R, or N to D or R
  • ON: Lock-up ON to OFF
  • OFF: Engine idling

-

Solenoid(SLP)

Shift solenoid valve SLP status

OFF or ON
  • ON: After engine start
  • OFF: Ignition switch ON

-

G Sensor Calibration

Deceleration Sensor Zero Point Calibration status

Incomplete or Complete

Complete

-

G Sensor Learning Value

Yaw rate and acceleration sensor learned value voltage

Min.: 0 V

Max.: 79.998 V

2.31 to 2.69 V: Deceleration Sensor Zero Point Calibration complete

-

CVT Oil Press Calibration

CVT Oil Pressure Calibration status

Incompl or Compl

Compl

-

HINT:

*: Refer to DTC P0705.

Click here 2020 - 2023 MY Corolla Corolla Hatchback [01/2019 - 11/2022]; K313 (CVT): CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: P0705; Transmission Range Sensor Circuit (PRNDL Input)

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Engine and ECT / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

Powertrain > Engine and ECT > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Connect the TC and TE1

Connects and disconnects terminals TC and TE1

ON or OFF
  • ON: TC and TE1 are connected.
  • OFF: TC and TE1 are disconnected.

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P

Activate the Solenoid (SLU)

Operates the shift solenoid valve SLU

ON or OFF

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P or N

Activate the Lock Up

Operates the lock-up

ON or OFF

Can be used to check lock-up operation.

Perform "Activate the Lock Up" while monitoring "Engine speed" and "SPD (NT)".

(Vehicle Condition)

  • Vehicle speed: 40 km/h (25 mph) or more

Activate the Solenoid (SL)

Operates the shift solenoid valve SL

ON or OFF

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P or N

Control the Shift Ratio (CVT)

Operates the shift solenoid valves to manually select a gear position (Low - Middle - High)
  • Press "→" button: Shift up
  • Press "←" button: Shift down

Used to check the operation of the shift solenoid valves.

NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.

HINT:

Perform "Control the Shift Ratio (CVT)" while monitoring "CVT Shift Status Ratio" to confirm the actual gear ratio.

(Vehicle Condition)

  • Vehicle speed between 20 km/h (10.8 mph) and 45 km/h (24.3 mph).

Control the SLS Pressure

Operates the shift solenoid valve SLS

High or Low

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P or N

Activate the Solenoid (SLS)

Operates the shift solenoid valve SLS

ON or OFF

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P or N

Activate the Solenoid(SC)

Operates the shift solenoid valve SC

ON or OFF

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P or N

Activate the Solenoid(SLP)

Operates the shift solenoid valve SLP

ON or OFF

(Vehicle Condition)

  • Ignition switch ON, engine stopped and shift lever in P or N