- DTC judgment completed
- System normal
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001GYI2 |
| Model Year Start: 2020 | Model: Corolla Hatchback | Prod Date Range: [01/2019 - 03/2019] |
| Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P020113-P020413,P062D13; Cylinder 1 Injector "A" Circuit Open; 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019] | ||
|
DTC |
P020113 |
Cylinder 1 Injector "A" Circuit Open |
|
DTC |
P020213 |
Cylinder 2 Injector "A" Circuit Open |
|
DTC |
P020313 |
Cylinder 3 Injector "A" Circuit Open |
|
DTC |
P020413 |
Cylinder 4 Injector "A" Circuit Open |
|
DTC |
P062D13 |
Fuel Injector Driver Circuit Performance Bank 1 Circuit Open |
DESCRIPTION
The D-4S system has two fuel injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines which fuel injection system to use in accordance with the engine conditions. The direct injection system uses an injector driver (EDU) built into the ECM to rapidly operate the direct fuel injector assemblies. It converts injection request signals from the ECM to high-voltage and high-current injector-drive signals that drive the direct fuel injector assemblies.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P020113 |
Cylinder 1 Injector "A" Circuit Open |
One of following conditions is met (1 trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P0201 |
|
P020213 |
Cylinder 2 Injector "A" Circuit Open |
One of following conditions is met (1 trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P0202 |
|
P020313 |
Cylinder 3 Injector "A" Circuit Open |
One of following conditions is met (1 trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P0203 |
|
P020413 |
Cylinder 4 Injector "A" Circuit Open |
One of following conditions is met (1 trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P0204 |
|
P062D13 |
Fuel Injector Driver Circuit Performance Bank 1 Circuit Open |
Open or short in direct fuel injector assembly (all cylinders) circuits for 60 times or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P062D |
*1: for Hatchback
*2: for Sedan
MONITOR DESCRIPTION
The fuel injection sequence occurs in numerical order from No. 1 to No. 4.
The ECM monitors the Injector Driver (EDU) at all times. If drivers or direct fuel injector assembly is malfunctioning, the EDU sends direct fuel injector assembly operation condition signals (fail signals) to the ECM. When the ECM receives the signals, the ECM stops the fuel injection control of the appropriate cylinders, cuts voltage to the appropriate IGN/INJ/D INJ relay*1 or D INJ relay*2, and illuminates the MIL.
- *1: for Hatchback
- *2: for Sedan
MONITOR STRATEGY
|
Related DTCs |
P0201: Injector circuit open (cylinder 1) P0202: Injector circuit open (cylinder 2) P0203: Injector circuit open (cylinder 3) P0204: Injector circuit open (cylinder 4) P062D: Injector driver performance |
|
Required Sensors/Components (Main) |
Direct fuel injector assembly ECM (injector driver) |
|
Required Sensors/Components (Related) |
- |
|
Frequency of Operation |
Continuous |
|
Duration |
- |
|
MIL Operation |
Immediate |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
P0201, P0202, P0203 and P0204
|
All of the following conditions are met |
- |
|
Confirmed injection |
2 times or more |
|
Either of the following conditions is met |
A or B |
|
A. All of the following conditions are met |
(a), (b) and (c) |
|
(a) Starter |
Off |
|
(b) Battery voltage |
10.5 V or higher |
|
(c) Time after condition (b) is met |
0.5 seconds or more |
|
B. All of the following conditions are met |
(d), (e) and (f) |
|
(d) Starter |
On |
|
(e) Battery voltage |
8 V or higher |
|
(f) Time after condition (e) is met |
0.5 seconds or more |
|
Engine speed |
100 to 6000 rpm |
|
Injection time |
0.00023 seconds or more |
|
Injector driver relay |
On |
|
Fuel injector driver performance fail (P062D) |
Not detected |
|
The other injector of the same INJECTOR DRIVER FAIL SIGNAL |
Not operating |
|
Ignition switch |
ON |
|
Time after ignition switch off to ON |
0.5 seconds or more |
P062D
|
Monitor runs whenever the following DTCs are not stored |
None |
|
All of the following conditions are met |
- |
|
Confirmed injection |
2 times or more |
|
Either of the following conditions is met |
A or B |
|
A. All of the following conditions are met |
(a), (b) and (c) |
|
(a) Starter |
Off |
|
(b) Battery voltage |
10.5 V or higher |
|
(c) Time after condition (b) is met |
0.5 seconds or more |
|
B. All of the following conditions are met |
(d), (e) and (f) |
|
(d) Starter |
On |
|
(e) Battery voltage |
8 V or higher |
|
(f) Time after condition (e) is met |
0.5 seconds or more |
|
Engine speed |
100 to 6000 rpm |
|
Injection time |
0.00023 seconds or more |
|
Injector driver relay |
On |
|
The other injector of the same INJECTOR DRIVER FAIL SIGNAL |
Not operating |
|
Ignition switch |
ON |
|
Time after ignition switch off to ON |
0.5 seconds or more |
TYPICAL MALFUNCTION THRESHOLDS
P0201, P0202, P0203 and P0204
|
One of the following conditions is met |
A, B or C |
|
A. No confirmed injection signal input |
20 times or more |
|
B. Both of the following conditions are met |
40 times or more |
|
Current injector voltage for the same INJECTOR DRIVER FAIL SIGNAL* detected by injector driver IC |
4.8 V or higher |
|
Last injector voltage for the same INJECTOR DRIVER FAIL SIGNAL* detected by injector driver IC |
4.8 V or higher |
|
C. Either of the following conditions is met |
(a) or (b) |
|
(a) Both of the following conditions are met |
20 times or more |
|
Current injector driver MOSFET current detected by injector driver IC |
30 A or more |
|
Last injector driver MOSFET current detected by injector driver IC |
30 A or more |
|
(b) Both of the following conditions are met |
1 and 2 |
|
1. Either of the following conditions is met |
20 times or more |
|
Current injector current during peak current control for the same INJECTOR DRIVER FAIL SIGNAL* detected by injector driver IC |
125 A or more |
|
Current injector current during hold current control for the same INJECTOR DRIVER FAIL SIGNAL* detected by injector driver IC |
100 A or more |
|
2. Either of the following conditions is met |
20 times or more |
|
Last injector current during peak current control for the same INJECTOR DRIVER FAIL SIGNAL* detected by injector driver IC |
125 A or more |
|
Last injector current during hold current control for the same INJECTOR DRIVER FAIL SIGNAL* detected by injector driver IC |
100 A or more |
P062D
|
No confirmed injection signal input in all cylinders |
60 times or more |
|
*: Definition of the INJECTOR DRIVER FAIL SIGNAL |
- |
|
INJECTOR DRIVER FAIL SIGNAL 1 |
#1 and #4 |
|
INJECTOR DRIVER FAIL SIGNAL 2 |
#2 and #3 |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
![2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Start the engine [A].
- Idle the engine for 15 seconds or more [B].
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P020113, P020213, P020313, P020413 or P062D13.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
-
[A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
-
If the current from the IGN/INJ/D INJ relay*1 or D INJ relay*2 is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.
- *1: for Hatchback
- *2: for Sedan
- Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK DTC OUTPUT (DTC P020113, P020213, P020313, P020413 AND/OR P062D13) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC P020113, P020213, P020313 or P020413 is output |
A |
|
3 or more of the following DTCs are output: P062D13, P020113, P020213, P020313 and P020413 (for Hatchback) |
B |
|
P062D13 is output (for Hatchback) |
|
|
3 or more of the following DTCs are output: P062D13, P020113, P020213, P020313 and P020413 (for Sedan) |
C |
|
P062D13 is output (for Sedan) |
| B |
|
| C |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR |
(a) Disconnect the ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C76-16 (#1D+) - C76-17 (#1D-) |
20°C (68°F) |
1.34 to 1.64 Ω |
|
C76-11 (#2D+) - C76-10 (#2D-) |
20°C (68°F) |
1.34 to 1.64 Ω |
|
C76-12 (#3D+) - C76-13 (#3D-) |
20°C (68°F) |
1.34 to 1.64 Ω |
|
C76-15 (#4D+) - C76-14 (#4D-) |
20°C (68°F) |
1.34 to 1.64 Ω |
|
C76-16 (#1D+) or C76-17 (#1D-) - Body ground and other terminals |
Always |
1 MΩ or higher |
|
C76-11 (#2D+) or C76-10 (#2D-) - Body ground and other terminals |
Always |
1 MΩ or higher |
|
C76-12 (#3D+) or C76-13 (#3D-) - Body ground and other terminals |
Always |
1 MΩ or higher |
|
C76-15 (#4D+) or C76-14 (#4D-) - Body ground and other terminals |
Always |
1 MΩ or higher |
HINT:
The standard values shown are direct fuel injector assembly resistance values.
| OK |
|
|
|
3. |
INSPECT DIRECT FUEL INJECTOR ASSEMBLY (RESISTANCE) |
(a) Check the resistance of the direct fuel injector assembly.
Click here
HINT:
Perform "Inspection After Repair" after replacing the direct fuel injector assembly.
Click here
| OK |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (DIRECT FUEL INJECTOR ASSEMBLY - ECM) |
| NG |
|
|
4. |
INSPECT IGN/INJ/D INJ RELAY |
(a) Inspect the IGN/INJ/D INJ relay.
Click here
| NG |
|
REPLACE IGN/INJ/D INJ RELAY |
|
|
5. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGN/INJ/D INJ RELAY) |
|
*1 |
No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
|
*2 |
IGN/INJ/D INJ Relay |
(a) Remove the IGN/INJ/D INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (IGN/INJ/D INJ relay) - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGN/INJ/D INJ RELAY) |
|
|
6. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGN/INJ/D INJ RELAY) |
|
*1 |
No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
|
*2 |
IGN/INJ/D INJ Relay |
(a) Remove the IGN/INJ/D INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 (IGN/INJ/D INJ relay) - Body ground |
Ignition switch ON |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY- IGN/INJ/D INJ RELAY) |
|
|
7. |
CHECK HARNESS AND CONNECTOR (IGN/INJ/D INJ RELAY - ECM) |
(a) Remove the IGN/INJ/D INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
5 (IGN/INJ/D INJ relay) - A47-53 (+BD1) |
Always |
Below 1 Ω |
|
2 (IGN/INJ/D INJ relay) - A47-34 (IREL) |
Always |
Below 1 Ω |
|
5 (IGN/INJ/D INJ relay) or A47-53 (+BD1) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
2 (IGN/INJ/D INJ relay) or A47-34 (IREL) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
8. |
INSPECT D INJ RELAY |
(a) Inspect the D INJ relay.
Click here
| NG |
|
REPLACE D INJ RELAY |
|
|
9. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY) |
|
*1 |
No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
|
*2 |
D INJ Relay |
(a) Remove the D INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (D INJ relay) - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - D INJ RELAY) |
|
|
10. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY) |
|
*1 |
No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
|
*2 |
D INJ Relay |
(a) Remove the D INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 (D INJ relay) - Body ground |
Ignition switch ON |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY- D INJ RELAY) |
|
|
11. |
CHECK HARNESS AND CONNECTOR (D INJ RELAY - ECM) |
(a) Remove the D INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
5 (D INJ relay) - A47-53 (+BD1) |
Always |
Below 1 Ω |
|
2 (D INJ relay) - A47-34 (IREL) |
Always |
Below 1 Ω |
|
5 (D INJ relay) or A47-53 (+BD1) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
2 (D INJ relay) or A47-34 (IREL) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|